* Free Software Foundation, Inc., *
* 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. *
***************************************************************************/
+
#ifdef HAVE_CONFIG_H
#include "config.h"
#endif
static int lpc32xx_controller_ready(struct nand_device *nand, int timeout);
static int lpc32xx_tc_ready(struct nand_device *nand, int timeout);
extern int nand_correct_data(struct nand_device *nand, u_char *dat,
- u_char *read_ecc, u_char *calc_ecc);
+ u_char *read_ecc, u_char *calc_ecc);
/* These are offset with the working area in IRAM when using DMA to
* read/write data to the SLC controller.
*/
NAND_DEVICE_COMMAND_HANDLER(lpc32xx_nand_device_command)
{
- if (CMD_ARGC < 3) {
+ if (CMD_ARGC < 3)
return ERROR_COMMAND_SYNTAX_ERROR;
- }
uint32_t osc_freq;
COMMAND_PARSE_NUMBER(u32, CMD_ARGV[2], osc_freq);
if ((lpc32xx_info->osc_freq < 1000) || (lpc32xx_info->osc_freq > 20000))
LOG_WARNING("LPC32xx oscillator frequency should be between "
- "1000 and 20000 kHz, was %i",
- lpc32xx_info->osc_freq);
+ "1000 and 20000 kHz, was %i",
+ lpc32xx_info->osc_freq);
lpc32xx_info->selected_controller = LPC32xx_NO_CONTROLLER;
lpc32xx_info->sw_write_protection = 0;
if (!lock)
LOG_WARNING("PLL is not locked");
- if (!bypass && direct) /* direct mode */
+ if (!bypass && direct) /* direct mode */
return (m * fclkin) / n;
- if (bypass && !direct) /* bypass mode */
+ if (bypass && !direct) /* bypass mode */
return fclkin / (2 * p);
- if (bypass & direct) /* direct bypass mode */
+ if (bypass & direct) /* direct bypass mode */
return fclkin;
- if (feedback) /* integer mode */
+ if (feedback) /* integer mode */
return m * (fclkin / n);
- else /* non-integer mode */
+ else /* non-integer mode */
return (m / (2 * p)) * (fclkin / n);
}
return ERROR_NAND_OPERATION_FAILED;
}
- if ((pwr_ctrl & (1 << 2)) == 0) { /* DIRECT RUN mode */
+ if ((pwr_ctrl & (1 << 2)) == 0) /* DIRECT RUN mode */
hclk = sysclk;
- } else {
+ else {
retval = target_read_u32(target, 0x40004058, &hclkpll_ctrl);
if (ERROR_OK != retval) {
LOG_ERROR("could not read HCLKPLL_CTRL");
return ERROR_NAND_OPERATION_FAILED;
}
- if (pwr_ctrl & (1 << 10)) /* ARM_CLK and HCLK use PERIPH_CLK */
+ if (pwr_ctrl & (1 << 10)) /* ARM_CLK and HCLK use PERIPH_CLK */
hclk = hclk_pll / (((hclkdiv_ctrl & 0x7c) >> 2) + 1);
- else /* HCLK uses HCLK_PLL */
+ else /* HCLK uses HCLK_PLL */
hclk = hclk_pll / (1 << (hclkdiv_ctrl & 0x3));
}
if (target->state != TARGET_HALTED) {
LOG_ERROR("target must be halted to use LPC32xx "
- "NAND flash controller");
+ "NAND flash controller");
return ERROR_NAND_OPERATION_FAILED;
}
/* select MLC controller if none is currently selected */
if (lpc32xx_info->selected_controller == LPC32xx_NO_CONTROLLER) {
LOG_DEBUG("no LPC32xx NAND flash controller selected, "
- "using default 'slc'");
+ "using default 'slc'");
lpc32xx_info->selected_controller = LPC32xx_SLC_CONTROLLER;
}
/* MLC_TIME_REG */
retval = target_write_u32(target, 0x200b8034,
- (twp & 0xf)
- | ((twh & 0xf) << 4)
- | ((trp & 0xf) << 8)
- | ((treh & 0xf) << 12)
- | ((trhz & 0x7) << 16)
- | ((trbwb & 0x1f) << 19)
- | ((tcea & 0x3) << 24));
+ (twp & 0xf)
+ | ((twh & 0xf) << 4)
+ | ((trp & 0xf) << 8)
+ | ((treh & 0xf) << 12)
+ | ((trhz & 0x7) << 16)
+ | ((trbwb & 0x1f) << 19)
+ | ((tcea & 0x3) << 24));
if (ERROR_OK != retval) {
LOG_ERROR("could not set MLC_TIME_REG");
return ERROR_NAND_OPERATION_FAILED;
WIDTH = bus_width)
*/
retval = target_write_u32(target, 0x20020014,
- 0x3e | (bus_width == 16) ? 1 : 0);
+ 0x3e | (bus_width == 16) ? 1 : 0);
if (ERROR_OK != retval) {
LOG_ERROR("could not set SLC_CFG");
return ERROR_NAND_OPERATION_FAILED;
/* SLC_TAC: SLC timing arcs register */
retval = target_write_u32(target, 0x2002002c,
- (r_setup & 0xf)
- | ((r_hold & 0xf) << 4)
- | ((r_width & 0xf) << 8)
- | ((r_rdy & 0xf) << 12)
- | ((w_setup & 0xf) << 16)
- | ((w_hold & 0xf) << 20)
- | ((w_width & 0xf) << 24)
- | ((w_rdy & 0xf) << 28));
+ (r_setup & 0xf)
+ | ((r_hold & 0xf) << 4)
+ | ((r_width & 0xf) << 8)
+ | ((r_rdy & 0xf) << 12)
+ | ((w_setup & 0xf) << 16)
+ | ((w_hold & 0xf) << 20)
+ | ((w_width & 0xf) << 24)
+ | ((w_rdy & 0xf) << 28));
if (ERROR_OK != retval) {
LOG_ERROR("could not set SLC_TAC");
return ERROR_NAND_OPERATION_FAILED;
if (target->state != TARGET_HALTED) {
LOG_ERROR("target must be halted to use "
- "LPC32xx NAND flash controller");
+ "LPC32xx NAND flash controller");
return ERROR_NAND_OPERATION_FAILED;
}
if (!lpc32xx_controller_ready(nand, 100)) {
LOG_ERROR("LPC32xx MLC NAND controller timed out "
- "after reset");
+ "after reset");
return ERROR_NAND_OPERATION_TIMEOUT;
}
} else if (lpc32xx_info->selected_controller == LPC32xx_SLC_CONTROLLER) {
return ERROR_NAND_OPERATION_FAILED;
}
- if (!lpc32xx_controller_ready(nand, 100))
- {
+ if (!lpc32xx_controller_ready(nand, 100)) {
LOG_ERROR("LPC32xx SLC NAND controller timed out "
- "after reset");
+ "after reset");
return ERROR_NAND_OPERATION_TIMEOUT;
}
}
if (target->state != TARGET_HALTED) {
LOG_ERROR("target must be halted to use "
- "LPC32xx NAND flash controller");
+ "LPC32xx NAND flash controller");
return ERROR_NAND_OPERATION_FAILED;
}
if (target->state != TARGET_HALTED) {
LOG_ERROR("target must be halted to use "
- "LPC32xx NAND flash controller");
+ "LPC32xx NAND flash controller");
return ERROR_NAND_OPERATION_FAILED;
}
if (target->state != TARGET_HALTED) {
LOG_ERROR("target must be halted to use "
- "LPC32xx NAND flash controller");
+ "LPC32xx NAND flash controller");
return ERROR_NAND_OPERATION_FAILED;
}
if (target->state != TARGET_HALTED) {
LOG_ERROR("target must be halted to use LPC32xx "
- "NAND flash controller");
+ "NAND flash controller");
return ERROR_NAND_OPERATION_FAILED;
}
}
static int lpc32xx_write_page_mlc(struct nand_device *nand, uint32_t page,
- uint8_t *data, uint32_t data_size,
- uint8_t *oob, uint32_t oob_size)
+ uint8_t *data, uint32_t data_size,
+ uint8_t *oob, uint32_t oob_size)
{
struct target *target = nand->target;
int retval;
return ERROR_NAND_OPERATION_FAILED;
}
retval = target_write_u32(target, 0x200b8004,
- (page >> 8) & 0xff);
+ (page >> 8) & 0xff);
if (ERROR_OK != retval) {
LOG_ERROR("could not set MLC_ADDR");
return ERROR_NAND_OPERATION_FAILED;
if (nand->address_cycles == 4) {
retval = target_write_u32(target, 0x200b8004,
- (page >> 16) & 0xff);
+ (page >> 16) & 0xff);
if (ERROR_OK != retval) {
LOG_ERROR("could not set MLC_ADDR");
return ERROR_NAND_OPERATION_FAILED;
return ERROR_NAND_OPERATION_FAILED;
}
retval = target_write_u32(target, 0x200b8004,
- (page >> 8) & 0xff);
+ (page >> 8) & 0xff);
if (ERROR_OK != retval) {
LOG_ERROR("could not set MLC_ADDR");
return ERROR_NAND_OPERATION_FAILED;
if (!lpc32xx_controller_ready(nand, 1000)) {
LOG_ERROR("timeout while waiting for "
- "completion of auto encode cycle");
+ "completion of auto encode cycle");
return ERROR_NAND_OPERATION_FAILED;
}
}
return ERROR_NAND_OPERATION_FAILED;
}
- if ((retval = nand_read_status(nand, &status)) != ERROR_OK) {
+ retval = nand_read_status(nand, &status);
+ if (retval != ERROR_OK) {
LOG_ERROR("couldn't read status");
return ERROR_NAND_OPERATION_FAILED;
}
if (status & NAND_STATUS_FAIL) {
LOG_ERROR("write operation didn't pass, status: 0x%2.2x",
- status);
+ status);
return ERROR_NAND_OPERATION_FAILED;
}
* target.
*/
static int lpc32xx_make_dma_list(uint32_t target_mem_base, uint32_t page_size,
- int do_read)
+ int do_read)
{
uint32_t i, dmasrc, ctrl, ecc_ctrl, oob_ctrl, dmadst;
*/
ctrl = (0x40 | 3 << 12 | 3 << 15 | 2 << 18 | 2 << 21 | 0 << 24
- | 0 << 25 | 0 << 26 | 0 << 27 | 0 << 31);
+ | 0 << 25 | 0 << 26 | 0 << 27 | 0 << 31);
/* DMACCxControl =
TransferSize =1,
Terminal count interrupt enable bit = 0
*/
ecc_ctrl = 0x01 | 1 << 12 | 1 << 15 | 2 << 18 | 2 << 21 | 0 << 24
- | 0 << 25 | 0 << 26 | 1 << 27 | 0 << 31;
+ | 0 << 25 | 0 << 26 | 1 << 27 | 0 << 31;
/* DMACCxControl =
TransferSize =16 for lp or 4 for sp,
Terminal count interrupt enable bit = 1 // set on last
*/
oob_ctrl = (page_size == 2048 ? 0x10 : 0x04)
- | 3 << 12 | 3 << 15 | 2 << 18 | 2 << 21 | 0 << 24
- | 0 << 25 | 0 << 26 | 0 << 27 | 1 << 31;
+ | 3 << 12 | 3 << 15 | 2 << 18 | 2 << 21 | 0 << 24
+ | 0 << 25 | 0 << 26 | 0 << 27 | 1 << 31;
if (do_read) {
- ctrl |= 1 << 27; /* Destination increment = 1 */
- oob_ctrl |= 1 << 27; /* Destination increment = 1 */
- dmasrc = 0x20020038; /* SLC_DMA_DATA */
+ ctrl |= 1 << 27;/* Destination increment = 1 */
+ oob_ctrl |= 1 << 27; /* Destination increment = 1 */
+ dmasrc = 0x20020038; /* SLC_DMA_DATA */
dmadst = target_mem_base + DATA_OFFS;
} else {
- ctrl |= 1 << 26; /* Source increment = 1 */
- oob_ctrl |= 1 << 26; /* Source increment = 1 */
+ ctrl |= 1 << 26;/* Source increment = 1 */
+ oob_ctrl |= 1 << 26; /* Source increment = 1 */
dmasrc = target_mem_base + DATA_OFFS;
- dmadst = 0x20020038; /* SLC_DMA_DATA */
+ dmadst = 0x20020038; /* SLC_DMA_DATA */
}
/*
* Write Operation Sequence for Small Block NAND
* data & 32 bytes of ECC data.
* 2. X'fer 64 bytes of Spare area from Flash to Memory.
*/
- for (i = 0; i < page_size/0x100; i++)
- {
+ for (i = 0; i < page_size/0x100; i++) {
dmalist[i*2].dma_src = (do_read ? dmasrc : (dmasrc + i * 256));
dmalist[i*2].dma_dest = (do_read ? (dmadst + i * 256) : dmadst);
dmalist[i*2].next_lli =
target_mem_base + (i*2 + 1) * sizeof(dmac_ll_t);
dmalist[i*2].next_ctrl = ctrl;
- dmalist[(i*2) + 1].dma_src = 0x20020034; /* SLC_ECC */
+ dmalist[(i*2) + 1].dma_src = 0x20020034;/* SLC_ECC */
dmalist[(i*2) + 1].dma_dest =
target_mem_base + ECC_OFFS + i * 4;
dmalist[(i*2) + 1].next_lli =
- target_mem_base + (i*2 + 2) * sizeof(dmac_ll_t);
+ target_mem_base + (i*2 + 2) * sizeof(dmac_ll_t);
dmalist[(i*2) + 1].next_ctrl = ecc_ctrl;
}
if (do_read)
- {
dmadst = target_mem_base + SPARE_OFFS;
- } else {
+ else {
dmasrc = target_mem_base + SPARE_OFFS;
- dmalist[(i*2) - 1].next_lli = 0; /* last link = null on write */
- dmalist[(i*2) - 1].next_ctrl |= (1 << 31); /* Set TC enable */
+ dmalist[(i*2) - 1].next_lli = 0;/* last link = null on write */
+ dmalist[(i*2) - 1].next_ctrl |= (1 << 31); /* Set TC enable */
}
dmalist[i*2].dma_src = dmasrc;
dmalist[i*2].dma_dest = dmadst;
dmalist[i*2].next_lli = 0;
dmalist[i*2].next_ctrl = oob_ctrl;
- return (i*2 + 1); /* Number of descriptors */
+ return i * 2 + 1; /* Number of descriptors */
}
static int lpc32xx_start_slc_dma(struct nand_device *nand, uint32_t count,
- int do_wait)
+ int do_wait)
{
struct target *target = nand->target;
int retval;
LOG_ERROR("Could not set DMACIntTCClear");
return retval;
}
-
+
/* DMACIntErrClear = ch0 */
retval = target_write_u32(target, 0x31000010, 1);
if (ERROR_OK != retval) {
LOG_ERROR("Could not set DMACIntErrClear");
return retval;
}
-
+
/* DMACCxConfig=
E=1,
SrcPeripheral = 1 (SLC),
H=0
*/
retval = target_write_u32(target, 0x31000110,
- 1 | 1<<1 | 1<<6 | 2<<11 | 0<<14
- | 0<<15 | 0<<16 | 0<<18);
+ 1 | 1<<1 | 1<<6 | 2<<11 | 0<<14
+ | 0<<15 | 0<<16 | 0<<18);
if (ERROR_OK != retval) {
LOG_ERROR("Could not set DMACC0Config");
return retval;
}
if ((tc_stat | err_stat) & 1) {
LOG_DEBUG("lpc32xx_dma_ready count=%d",
- timeout);
+ timeout);
if (err_stat & 1) {
LOG_ERROR("lpc32xx_dma_ready "
- "DMA error, aborted");
+ "DMA error, aborted");
return 0;
- } else {
+ } else
return 1;
- }
}
alive_sleep(1);
return 0;
}
-static uint32_t slc_ecc_copy_to_buffer(uint8_t * spare,
- const uint32_t * ecc, int count)
+static uint32_t slc_ecc_copy_to_buffer(uint8_t *spare,
+ const uint32_t *ecc, int count)
{
int i;
for (i = 0; i < (count * 3); i += 3) {
int addr = 0;
while (oob_size > 0) {
LOG_DEBUG("%02x: %02x %02x %02x %02x %02x %02x %02x %02x", addr,
- oob[0], oob[1], oob[2], oob[3],
- oob[4], oob[5], oob[6], oob[7]);
+ oob[0], oob[1], oob[2], oob[3],
+ oob[4], oob[5], oob[6], oob[7]);
oob += 8;
addr += 8;
oob_size -= 8;
- }
+ }
}
static int lpc32xx_write_page_slc(struct nand_device *nand,
- struct working_area *pworking_area,
- uint32_t page, uint8_t *data,
- uint32_t data_size, uint8_t *oob,
- uint32_t oob_size)
+ struct working_area *pworking_area,
+ uint32_t page, uint8_t *data,
+ uint32_t data_size, uint8_t *oob,
+ uint32_t oob_size)
{
struct target *target = nand->target;
int retval;
uint32_t target_mem_base;
LOG_DEBUG("SLC write page %x data=%d, oob=%d, "
- "data_size=%d, oob_size=%d",
- page, data != 0, oob != 0, data_size, oob_size);
+ "data_size=%d, oob_size=%d",
+ page, data != 0, oob != 0, data_size, oob_size);
target_mem_base = pworking_area->address;
- /*
+ /*
* Skip writting page which has all 0xFF data as this will
* generate 0x0 value.
*/
break;
}
if (all_ff)
- return ERROR_OK;
+ return ERROR_OK;
}
/* Make the dma descriptors in local memory */
int nll = lpc32xx_make_dma_list(target_mem_base, nand->page_size, 0);
XXX: Assumes host and target have same byte sex.
*/
retval = target_write_memory(target, target_mem_base, 4,
- nll * sizeof(dmac_ll_t) / 4,
- (uint8_t *)dmalist);
+ nll * sizeof(dmac_ll_t) / 4,
+ (uint8_t *)dmalist);
if (ERROR_OK != retval) {
LOG_ERROR("Could not write DMA descriptors to IRAM");
return retval;
return retval;
}
- /* SLC_CFG =
- Force nCE assert,
- DMA ECC enabled,
- ECC enabled,
- DMA burst enabled,
- DMA write to SLC,
- WIDTH = bus_width
+ /* SLC_CFG =
+ Force nCE assert,
+ DMA ECC enabled,
+ ECC enabled,
+ DMA burst enabled,
+ DMA write to SLC,
+ WIDTH = bus_width
*/
retval = target_write_u32(target, 0x20020014, 0x3c);
if (ERROR_OK != retval) {
memset(fdata, 0xFF, nand->page_size);
memcpy(fdata, data, data_size);
retval = target_write_memory(target,
- target_mem_base + DATA_OFFS,
- 4, nand->page_size/4, fdata);
+ target_mem_base + DATA_OFFS,
+ 4, nand->page_size/4, fdata);
if (ERROR_OK != retval) {
LOG_ERROR("Could not write data to IRAM");
return retval;
/* Write first decriptor to DMA controller */
retval = target_write_memory(target, 0x31000100, 4,
- sizeof(dmac_ll_t) / 4,
- (uint8_t *)dmalist);
+ sizeof(dmac_ll_t) / 4,
+ (uint8_t *)dmalist);
if (ERROR_OK != retval) {
LOG_ERROR("Could not write DMA descriptor to DMAC");
return retval;
LOG_ERROR("DMA failed");
return retval;
}
-
+
/* Wait for DMA to finish. SLC is not finished at this stage */
if (!lpc32xx_dma_ready(nand, 100)) {
LOG_ERROR("Data DMA failed during write");
return ERROR_FLASH_OPERATION_FAILED;
}
- } /* data xfer */
+ } /* data xfer */
/* Copy OOB to iram */
static uint8_t foob[64];
int foob_size = nand->page_size == 2048 ? 64 : 16;
memset(foob, 0xFF, foob_size);
- if (oob) { /* Raw mode */
+ if (oob) /* Raw mode */
memcpy(foob, oob, oob_size);
- } else {
+ else {
/* Get HW generated ECC, made while writing data */
int ecc_count = nand->page_size == 2048 ? 8 : 2;
static uint32_t hw_ecc[8];
retval = target_read_memory(target, target_mem_base + ECC_OFFS,
- 4, ecc_count, (uint8_t *)hw_ecc);
+ 4, ecc_count, (uint8_t *)hw_ecc);
if (ERROR_OK != retval) {
LOG_ERROR("Reading hw generated ECC from IRAM failed");
return retval;
lpc32xx_dump_oob(foob, foob_size);
}
retval = target_write_memory(target, target_mem_base + SPARE_OFFS, 4,
- foob_size / 4, foob);
+ foob_size / 4, foob);
if (ERROR_OK != retval) {
LOG_ERROR("Writing OOB to IRAM failed");
return retval;
/* Write OOB decriptor to DMA controller */
retval = target_write_memory(target, 0x31000100, 4,
- sizeof(dmac_ll_t) / 4,
- (uint8_t *)(&dmalist[nll-1]));
+ sizeof(dmac_ll_t) / 4,
+ (uint8_t *)(&dmalist[nll-1]));
if (ERROR_OK != retval) {
LOG_ERROR("Could not write OOB DMA descriptor to DMAC");
return retval;
return retval;
}
/* DMACCxConfig=
- E=1,
- SrcPeripheral = 1 (SLC),
- DestPeripheral = 1 (SLC),
- FlowCntrl = 2 (Pher -> Mem, DMA),
- IE = 0,
- ITC = 0,
- L= 0,
- H=0
+ * E=1,
+ * SrcPeripheral = 1 (SLC),
+ * DestPeripheral = 1 (SLC),
+ * FlowCntrl = 2 (Pher -> Mem, DMA),
+ * IE = 0,
+ * ITC = 0,
+ * L= 0,
+ * H=0
*/
retval = target_write_u32(target, 0x31000110,
- 1 | 1<<1 | 1<<6 | 2<<11 | 0<<14
- | 0<<15 | 0<<16 | 0<<18);
+ 1 | 1<<1 | 1<<6 | 2<<11 | 0<<14
+ | 0<<15 | 0<<16 | 0<<18);
if (ERROR_OK != retval) {
LOG_ERROR("Could not set DMACC0Config");
return retval;
/* Wait finish */
if (!lpc32xx_tc_ready(nand, 100)) {
LOG_ERROR("timeout while waiting for "
- "completion of DMA");
+ "completion of DMA");
return ERROR_NAND_OPERATION_FAILED;
}
} else {
}
static int lpc32xx_write_page(struct nand_device *nand, uint32_t page,
- uint8_t *data, uint32_t data_size,
- uint8_t *oob, uint32_t oob_size)
+ uint8_t *data, uint32_t data_size,
+ uint8_t *oob, uint32_t oob_size)
{
struct lpc32xx_nand_controller *lpc32xx_info = nand->controller_priv;
struct target *target = nand->target;
if (target->state != TARGET_HALTED) {
LOG_ERROR("target must be halted to use LPC32xx "
- "NAND flash controller");
+ "NAND flash controller");
return ERROR_NAND_OPERATION_FAILED;
}
} else if (lpc32xx_info->selected_controller == LPC32xx_MLC_CONTROLLER) {
if (!data && oob) {
LOG_ERROR("LPC32xx MLC controller can't write "
- "OOB data only");
+ "OOB data only");
return ERROR_NAND_OPERATION_NOT_SUPPORTED;
}
if (oob && (oob_size > 24)) {
LOG_ERROR("LPC32xx MLC controller can't write more "
- "than 6 bytes for each quarter's OOB data");
+ "than 6 bytes for each quarter's OOB data");
return ERROR_NAND_OPERATION_NOT_SUPPORTED;
}
}
retval = lpc32xx_write_page_mlc(nand, page, data, data_size,
- oob, oob_size);
+ oob, oob_size);
} else if (lpc32xx_info->selected_controller == LPC32xx_SLC_CONTROLLER) {
struct working_area *pworking_area;
if (!data && oob) {
* Anyway the code supports the oob only mode below.
*/
return nand_write_page_raw(nand, page, data,
- data_size, oob, oob_size);
+ data_size, oob, oob_size);
}
retval = target_alloc_working_area(target,
- nand->page_size + DATA_OFFS,
- &pworking_area);
+ nand->page_size + DATA_OFFS,
+ &pworking_area);
if (retval != ERROR_OK) {
LOG_ERROR("Can't allocate working area in "
- "LPC internal RAM");
+ "LPC internal RAM");
return ERROR_FLASH_OPERATION_FAILED;
}
retval = lpc32xx_write_page_slc(nand, pworking_area, page,
- data, data_size, oob, oob_size);
+ data, data_size, oob, oob_size);
target_free_working_area(target, pworking_area);
}
}
static int lpc32xx_read_page_mlc(struct nand_device *nand, uint32_t page,
- uint8_t *data, uint32_t data_size,
- uint8_t *oob, uint32_t oob_size)
+ uint8_t *data, uint32_t data_size,
+ uint8_t *oob, uint32_t oob_size)
{
struct target *target = nand->target;
static uint8_t page_buffer[2048];
return ERROR_NAND_OPERATION_FAILED;
}
if (nand->page_size == 512) {
- /* small page device */
- /* MLC_ADDR = 0x0 (one column cycle) */
+ /* small page device
+ * MLC_ADDR = 0x0 (one column cycle) */
retval = target_write_u32(target, 0x200b8004, 0x0);
if (ERROR_OK != retval) {
LOG_ERROR("could not set MLC_ADDR");
return ERROR_NAND_OPERATION_FAILED;
}
retval = target_write_u32(target, 0x200b8004,
- (page >> 8) & 0xff);
+ (page >> 8) & 0xff);
if (ERROR_OK != retval) {
LOG_ERROR("could not set MLC_ADDR");
return ERROR_NAND_OPERATION_FAILED;
if (nand->address_cycles == 4) {
retval = target_write_u32(target, 0x200b8004,
- (page >> 16) & 0xff);
+ (page >> 16) & 0xff);
if (ERROR_OK != retval) {
LOG_ERROR("could not set MLC_ADDR");
return ERROR_NAND_OPERATION_FAILED;
}
}
} else {
- /* large page device */
- /* MLC_ADDR = 0x0 (two column cycles) */
+ /* large page device
+ * MLC_ADDR = 0x0 (two column cycles) */
retval = target_write_u32(target, 0x200b8004, 0x0);
if (ERROR_OK != retval) {
LOG_ERROR("could not set MLC_ADDR");
return ERROR_NAND_OPERATION_FAILED;
}
retval = target_write_u32(target, 0x200b8004,
- (page >> 8) & 0xff);
+ (page >> 8) & 0xff);
if (ERROR_OK != retval) {
LOG_ERROR("could not set MLC_ADDR");
return ERROR_NAND_OPERATION_FAILED;
/* MLC_CMD = Read Start */
retval = target_write_u32(target, 0x200b8000,
- NAND_CMD_READSTART);
+ NAND_CMD_READSTART);
if (ERROR_OK != retval) {
LOG_ERROR("could not set MLC_CMD");
return ERROR_NAND_OPERATION_FAILED;
if (!lpc32xx_controller_ready(nand, 1000)) {
LOG_ERROR("timeout while waiting for "
- "completion of auto decode cycle");
+ "completion of auto decode cycle");
return ERROR_NAND_OPERATION_FAILED;
}
if (mlc_isr & 0x8) {
if (mlc_isr & 0x40) {
LOG_ERROR("uncorrectable error detected: "
- "0x%2.2x", (unsigned)mlc_isr);
+ "0x%2.2x", (unsigned)mlc_isr);
return ERROR_NAND_OPERATION_FAILED;
}
LOG_WARNING("%i symbol error detected and corrected",
- ((int)(((mlc_isr & 0x30) >> 4) + 1)));
+ ((int)(((mlc_isr & 0x30) >> 4) + 1)));
}
if (data) {
retval = target_read_memory(target, 0x200a8000, 4, 128,
- page_buffer + page_bytes_done);
+ page_buffer + page_bytes_done);
if (ERROR_OK != retval) {
LOG_ERROR("could not read MLC_BUF (data)");
return ERROR_NAND_OPERATION_FAILED;
if (oob) {
retval = target_read_memory(target, 0x200a8000, 4, 4,
- oob_buffer + oob_bytes_done);
+ oob_buffer + oob_bytes_done);
if (ERROR_OK != retval) {
LOG_ERROR("could not read MLC_BUF (oob)");
return ERROR_NAND_OPERATION_FAILED;
}
static int lpc32xx_read_page_slc(struct nand_device *nand,
- struct working_area *pworking_area,
- uint32_t page, uint8_t *data,
- uint32_t data_size, uint8_t *oob,
- uint32_t oob_size)
+ struct working_area *pworking_area,
+ uint32_t page, uint8_t *data,
+ uint32_t data_size, uint8_t *oob,
+ uint32_t oob_size)
{
struct target *target = nand->target;
int retval;
uint32_t target_mem_base;
LOG_DEBUG("SLC read page %x data=%d, oob=%d",
- page, data_size, oob_size);
+ page, data_size, oob_size);
target_mem_base = pworking_area->address;
XXX: Assumes host and target have same byte sex.
*/
retval = target_write_memory(target, target_mem_base, 4,
- nll * sizeof(dmac_ll_t) / 4,
- (uint8_t *)dmalist);
+ nll * sizeof(dmac_ll_t) / 4,
+ (uint8_t *)dmalist);
if (ERROR_OK != retval) {
LOG_ERROR("Could not write DMA descriptors to IRAM");
return retval;
return retval;
}
- /* SLC_CFG =
- Force nCE assert,
- DMA ECC enabled,
- ECC enabled,
- DMA burst enabled,
- DMA read from SLC,
- WIDTH = bus_width
+ /* SLC_CFG =
+ Force nCE assert,
+ DMA ECC enabled,
+ ECC enabled,
+ DMA burst enabled,
+ DMA read from SLC,
+ WIDTH = bus_width
*/
retval = target_write_u32(target, 0x20020014, 0x3e);
if (ERROR_OK != retval) {
/* Write first decriptor to DMA controller */
retval = target_write_memory(target, 0x31000100, 4,
- sizeof(dmac_ll_t) / 4, (uint8_t *)dmalist);
+ sizeof(dmac_ll_t) / 4, (uint8_t *)dmalist);
if (ERROR_OK != retval) {
LOG_ERROR("Could not write DMA descriptor to DMAC");
return retval;
/* Copy data from iram */
if (data) {
retval = target_read_memory(target, target_mem_base + DATA_OFFS,
- 4, data_size/4, data);
+ 4, data_size/4, data);
if (ERROR_OK != retval) {
LOG_ERROR("Could not read data from IRAM");
return retval;
if (oob) {
/* No error correction, just return data as read from flash */
retval = target_read_memory(target,
- target_mem_base + SPARE_OFFS, 4,
- oob_size/4, oob);
+ target_mem_base + SPARE_OFFS, 4,
+ oob_size/4, oob);
if (ERROR_OK != retval) {
LOG_ERROR("Could not read OOB from IRAM");
return retval;
/* Copy OOB from flash, stored in IRAM */
static uint8_t foob[64];
retval = target_read_memory(target, target_mem_base + SPARE_OFFS,
- 4, nand->page_size == 2048 ? 16 : 4, foob);
+ 4, nand->page_size == 2048 ? 16 : 4, foob);
lpc32xx_dump_oob(foob, nand->page_size == 2048 ? 64 : 16);
if (ERROR_OK != retval) {
LOG_ERROR("Could not read OOB from IRAM");
}
/* Copy ECC from HW, generated while reading */
int ecc_count = nand->page_size == 2048 ? 8 : 2;
- static uint32_t hw_ecc[8]; /* max size */
+ static uint32_t hw_ecc[8]; /* max size */
retval = target_read_memory(target, target_mem_base + ECC_OFFS, 4,
- ecc_count, (uint8_t *)hw_ecc);
+ ecc_count, (uint8_t *)hw_ecc);
if (ERROR_OK != retval) {
LOG_ERROR("Could not read hw generated ECC from IRAM");
return retval;
static uint8_t ecc[24];
slc_ecc_copy_to_buffer(ecc, hw_ecc, ecc_count);
/* Copy ECC from flash using correct layout */
- static uint8_t fecc[24]; /* max size */
+ static uint8_t fecc[24];/* max size */
int *layout = nand->page_size == 2048 ? lp_ooblayout : sp_ooblayout;
int i;
for (i = 0; i < ecc_count * 3; i++)
/* Compare ECC and possibly correct data */
for (i = 0; i < ecc_count; i++) {
retval = nand_correct_data(nand, data + 256*i, &fecc[i * 3],
- &ecc[i * 3]);
+ &ecc[i * 3]);
if (retval > 0)
LOG_WARNING("error detected and corrected: %d/%d",
- page, i);
+ page, i);
if (retval < 0)
break;
}
}
static int lpc32xx_read_page(struct nand_device *nand, uint32_t page,
- uint8_t *data, uint32_t data_size,
- uint8_t *oob, uint32_t oob_size)
+ uint8_t *data, uint32_t data_size,
+ uint8_t *oob, uint32_t oob_size)
{
struct lpc32xx_nand_controller *lpc32xx_info = nand->controller_priv;
struct target *target = nand->target;
if (target->state != TARGET_HALTED) {
LOG_ERROR("target must be halted to use LPC32xx "
- "NAND flash controller");
+ "NAND flash controller");
return ERROR_NAND_OPERATION_FAILED;
}
return ERROR_NAND_OPERATION_NOT_SUPPORTED;
}
retval = lpc32xx_read_page_mlc(nand, page, data, data_size,
- oob, oob_size);
+ oob, oob_size);
} else if (lpc32xx_info->selected_controller == LPC32xx_SLC_CONTROLLER) {
struct working_area *pworking_area;
- retval = target_alloc_working_area(target,
- nand->page_size + 0x200,
- &pworking_area);
+ retval = target_alloc_working_area(target,
+ nand->page_size + 0x200,
+ &pworking_area);
if (retval != ERROR_OK) {
LOG_ERROR("Can't allocate working area in "
- "LPC internal RAM");
+ "LPC internal RAM");
return ERROR_FLASH_OPERATION_FAILED;
}
retval = lpc32xx_read_page_slc(nand, pworking_area, page,
- data, data_size, oob, oob_size);
- target_free_working_area(target, pworking_area);
+ data, data_size, oob, oob_size);
+ target_free_working_area(target, pworking_area);
}
return retval;
if (target->state != TARGET_HALTED) {
LOG_ERROR("target must be halted to use LPC32xx "
- "NAND flash controller");
+ "NAND flash controller");
return ERROR_NAND_OPERATION_FAILED;
}
if (status & 2) {
LOG_DEBUG("lpc32xx_controller_ready count=%d",
- timeout);
+ timeout);
return 1;
}
} else if (lpc32xx_info->selected_controller == LPC32xx_SLC_CONTROLLER) {
if (status & 1) {
LOG_DEBUG("lpc32xx_controller_ready count=%d",
- timeout);
+ timeout);
return 1;
}
}
if (target->state != TARGET_HALTED) {
LOG_ERROR("target must be halted to use LPC32xx "
- "NAND flash controller");
+ "NAND flash controller");
return ERROR_NAND_OPERATION_FAILED;
}
if (status & 1) {
LOG_DEBUG("lpc32xx_nand_ready count end=%d",
- timeout);
+ timeout);
return 1;
}
} else if (lpc32xx_info->selected_controller == LPC32xx_SLC_CONTROLLER) {
if (status & 1) {
LOG_DEBUG("lpc32xx_nand_ready count end=%d",
- timeout);
+ timeout);
return 1;
}
}
LOG_ERROR("Could not read SLC_INT_STAT");
return 0;
}
- if (status & 2){
+ if (status & 2) {
LOG_DEBUG("lpc32xx_tc_ready count=%d", timeout);
return 1;
}
"no", "mlc", "slc"
};
- if ((CMD_ARGC < 1) || (CMD_ARGC > 3)) {
+ if ((CMD_ARGC < 1) || (CMD_ARGC > 3))
return ERROR_COMMAND_SYNTAX_ERROR;
- }
unsigned num;
COMMAND_PARSE_NUMBER(uint, CMD_ARGV[0], num);
struct nand_device *nand = get_nand_device_by_num(num);
if (!nand) {
command_print(CMD_CTX, "nand device '#%s' is out of bounds",
- CMD_ARGV[0]);
+ CMD_ARGV[0]);
return ERROR_OK;
}
} else if (strcmp(CMD_ARGV[1], "slc") == 0) {
lpc32xx_info->selected_controller =
LPC32xx_SLC_CONTROLLER;
- } else {
+ } else
return ERROR_COMMAND_SYNTAX_ERROR;
- }
}
command_print(CMD_CTX, "%s controller selected",
- selected[lpc32xx_info->selected_controller]);
+ selected[lpc32xx_info->selected_controller]);
return ERROR_OK;
}
Code Review / openocd.git / blobdiff