flash/nor: flash driver for Synwit SWM050 MCUs

[openocd.git] / doc / openocd.texi

diff --git a/doc/openocd.texi b/doc/openocd.texi
index 57d1b09591cd0327f00df3737243c882b16fb52f..c5a926ca86b5e3a8b7d4075f3451fbfe1d58fd5e 100644 (file)
--- a/doc/openocd.texi
+++ b/doc/openocd.texi
@@ -3479,7 +3479,7 @@ How long (in milliseconds) OpenOCD should wait after deasserting
 nTRST (active-low JTAG TAP reset) before starting new JTAG operations.
 @end deffn
 
-@anchor {reset_config}
+@anchor{reset_config}
 @deffn {Command} reset_config mode_flag ...
 This command displays or modifies the reset configuration
 of your combination of JTAG board and target in target
@@ -7002,6 +7002,23 @@ unlock str9 device.
 
 @end deffn
 
+@deffn {Flash Driver} swm050
+@cindex swm050
+All members of the swm050 microcontroller family from Foshan Synwit Tech.
+
+@example
+flash bank $_FLASHNAME swm050 0x0 0x2000 0 0 $_TARGETNAME
+@end example
+
+One swm050-specific command is defined:
+
+@deffn Command {swm050 mass_erase} bank_id
+Erases the entire flash bank.
+@end deffn
+
+@end deffn
+
+
 @deffn {Flash Driver} tms470
 Most members of the TMS470 microcontroller family from Texas Instruments
 include internal flash and use ARM7TDMI cores.
@@ -7482,67 +7499,6 @@ or @code{read_page} methods, so @command{nand raw_access} won't
 change any behavior.
 @end deffn
 
-@section mFlash
-
-@subsection mFlash Configuration
-@cindex mFlash Configuration
-
-@deffn {Config Command} {mflash bank} soc base RST_pin target
-Configures a mflash for @var{soc} host bank at
-address @var{base}.
-The pin number format depends on the host GPIO naming convention.
-Currently, the mflash driver supports s3c2440 and pxa270.
-
-Example for s3c2440 mflash where @var{RST pin} is GPIO B1:
-
-@example
-mflash bank $_FLASHNAME s3c2440 0x10000000 1b 0
-@end example
-
-Example for pxa270 mflash where @var{RST pin} is GPIO 43:
-
-@example
-mflash bank $_FLASHNAME pxa270 0x08000000 43 0
-@end example
-@end deffn
-
-@subsection mFlash commands
-@cindex mFlash commands
-
-@deffn Command {mflash config pll} frequency
-Configure mflash PLL.
-The @var{frequency} is the mflash input frequency, in Hz.
-Issuing this command will erase mflash's whole internal nand and write new pll.
-After this command, mflash needs power-on-reset for normal operation.
-If pll was newly configured, storage and boot(optional) info also need to be update.
-@end deffn
-
-@deffn Command {mflash config boot}
-Configure bootable option.
-If bootable option is set, mflash offer the first 8 sectors
-(4kB) for boot.
-@end deffn
-
-@deffn Command {mflash config storage}
-Configure storage information.
-For the normal storage operation, this information must be
-written.
-@end deffn
-
-@deffn Command {mflash dump} num filename offset size
-Dump @var{size} bytes, starting at @var{offset} bytes from the
-beginning of the bank @var{num}, to the file named @var{filename}.
-@end deffn
-
-@deffn Command {mflash probe}
-Probe mflash.
-@end deffn
-
-@deffn Command {mflash write} num filename offset
-Write the binary file @var{filename} to mflash bank @var{num}, starting at
-@var{offset} bytes from the beginning of the bank.
-@end deffn
-
 @node Flash Programming
 @chapter Flash Programming