nTRST (active-low JTAG TAP reset) before starting new JTAG operations.
@end deffn
-@anchor {reset_config}
+@anchor{reset_config}
@deffn {Command} reset_config mode_flag ...
This command displays or modifies the reset configuration
of your combination of JTAG board and target in target
@end deffn
+@deffn {Flash Driver} swm050
+@cindex swm050
+All members of the swm050 microcontroller family from Foshan Synwit Tech.
+
+@example
+flash bank $_FLASHNAME swm050 0x0 0x2000 0 0 $_TARGETNAME
+@end example
+
+One swm050-specific command is defined:
+
+@deffn Command {swm050 mass_erase} bank_id
+Erases the entire flash bank.
+@end deffn
+
+@end deffn
+
+
@deffn {Flash Driver} tms470
Most members of the TMS470 microcontroller family from Texas Instruments
include internal flash and use ARM7TDMI cores.
change any behavior.
@end deffn
-@section mFlash
-
-@subsection mFlash Configuration
-@cindex mFlash Configuration
-
-@deffn {Config Command} {mflash bank} soc base RST_pin target
-Configures a mflash for @var{soc} host bank at
-address @var{base}.
-The pin number format depends on the host GPIO naming convention.
-Currently, the mflash driver supports s3c2440 and pxa270.
-
-Example for s3c2440 mflash where @var{RST pin} is GPIO B1:
-
-@example
-mflash bank $_FLASHNAME s3c2440 0x10000000 1b 0
-@end example
-
-Example for pxa270 mflash where @var{RST pin} is GPIO 43:
-
-@example
-mflash bank $_FLASHNAME pxa270 0x08000000 43 0
-@end example
-@end deffn
-
-@subsection mFlash commands
-@cindex mFlash commands
-
-@deffn Command {mflash config pll} frequency
-Configure mflash PLL.
-The @var{frequency} is the mflash input frequency, in Hz.
-Issuing this command will erase mflash's whole internal nand and write new pll.
-After this command, mflash needs power-on-reset for normal operation.
-If pll was newly configured, storage and boot(optional) info also need to be update.
-@end deffn
-
-@deffn Command {mflash config boot}
-Configure bootable option.
-If bootable option is set, mflash offer the first 8 sectors
-(4kB) for boot.
-@end deffn
-
-@deffn Command {mflash config storage}
-Configure storage information.
-For the normal storage operation, this information must be
-written.
-@end deffn
-
-@deffn Command {mflash dump} num filename offset size
-Dump @var{size} bytes, starting at @var{offset} bytes from the
-beginning of the bank @var{num}, to the file named @var{filename}.
-@end deffn
-
-@deffn Command {mflash probe}
-Probe mflash.
-@end deffn
-
-@deffn Command {mflash write} num filename offset
-Write the binary file @var{filename} to mflash bank @var{num}, starting at
-@var{offset} bytes from the beginning of the bank.
-@end deffn
-
@node Flash Programming
@chapter Flash Programming
@option{on}.
@end deffn
+@deffn Command {$target_name catch_exc} [@option{off}|@option{sec_el1}|@option{sec_el3}|@option{nsec_el1}|@option{nsec_el2}]+
+Cause @command{$target_name} to halt when an exception is taken. Any combination of
+Secure (sec) EL1/EL3 or Non-Secure (nsec) EL1/EL2 is valid. The target
+@command{$target_name} will halt before taking the exception. In order to resume
+the target, the exception catch must be disabled again with @command{$target_name catch_exc off}.
+Issuing the command without options prints the current configuration.
+@end deffn
+
@section EnSilica eSi-RISC Architecture
eSi-RISC is a highly configurable microprocessor architecture for embedded systems
@deffn Command {esirisc trace init}
Initialize trace collection. This command must be called any time the
-configuration changes. If an trace buffer has been configured, the contents will
+configuration changes. If a trace buffer has been configured, the contents will
be overwritten when trace collection starts.
@end deffn
@option{size} options using DMA.
@end deffn
-@deffn Command {$target_name catch_exc} [@option{off}|@option{sec_el1}|@option{sec_el3}|@option{nsec_el1}|@option{nsec_el2}]+
-Cause @command{$target_name} to halt when an exception is taken. Any combination of
-Secure (sec) EL1/EL3 or Non-Secure (nsec) EL1/EL2 is valid. The target
-@command{$target_name} will halt before taking the exception. In order to resume
-the target, the exception catch must be disabled again with @command{$target_name catch_exc off}.
-Issuing the command without options prints the current configuration.
-@end deffn
-
@section Intel Architecture
Intel Quark X10xx is the first product in the Quark family of SoCs. It is an IA-32