nTRST (active-low JTAG TAP reset) before starting new JTAG operations.
@end deffn
+@anchor {reset_config}
@deffn {Command} reset_config mode_flag ...
This command displays or modifies the reset configuration
of your combination of JTAG board and target in target
@deffn {Flash Driver} lpc2000
This is the driver to support internal flash of all members of the
LPC11(x)00 and LPC1300 microcontroller families and most members of
-the LPC800, LPC1500, LPC1700, LPC1800, LPC2000, LPC4000 and LPC54100
-microcontroller families from NXP.
+the LPC800, LPC1500, LPC1700, LPC1800, LPC2000, LPC4000, LPC54100,
+LPC8Nxx and NHS31xx microcontroller families from NXP.
@quotation Note
There are LPC2000 devices which are not supported by the @var{lpc2000}
@option{lpc54100} (LPC541xx)
@option{lpc4000} (LPC40xx)
or @option{auto} - automatically detects flash variant and size for LPC11(x)00,
-LPC8xx, LPC13xx, LPC17xx and LPC40xx
+LPC8xx, LPC13xx, LPC17xx, LPC40xx, LPC8Nxx and NHS31xx
@item @var{clock_kHz} ... the frequency, in kiloHertz,
at which the core is running
@item @option{calc_checksum} ... optional (but you probably want to provide this!),
@end deffn
@end deffn
+@deffn {Flash Driver} w600
+W60x series Wi-Fi SoC from WinnerMicro
+are designed with ARM Cortex-M3 and have 1M Byte QFLASH inside.
+The @var{w600} driver uses the @var{target} parameter to select the
+correct bank config.
+
+@example
+flash bank $_FLASHNAME w600 0x08000000 0 0 0 $_TARGETNAMEs
+@end example
+@end deffn
+
@deffn {Flash Driver} xmc1xxx
All members of the XMC1xxx microcontroller family from Infineon.
This driver does not require the chip and bus width to be specified.
This finishes by listing the current vector catch configuration.
@end deffn
-@deffn Command {cortex_m reset_config} (@option{srst}|@option{sysresetreq}|@option{vectreset})
-Control reset handling. The default @option{srst} is to use srst if fitted,
-otherwise fallback to @option{vectreset}.
+@deffn Command {cortex_m reset_config} (@option{sysresetreq}|@option{vectreset})
+Control reset handling if hardware srst is not fitted
+@xref{reset_config,,reset_config}.
+
@itemize @minus
-@item @option{srst} use hardware srst if fitted otherwise fallback to @option{vectreset}.
-@item @option{sysresetreq} use NVIC SYSRESETREQ to reset system.
-@item @option{vectreset} use NVIC VECTRESET to reset system.
+@item @option{sysresetreq} use AIRCR SYSRESETREQ to reset system.
+@item @option{vectreset} use AIRCR VECTRESET to reset system (default).
@end itemize
-Using @option{vectreset} is a safe option for all current Cortex-M cores.
+
+Using @option{vectreset} is a safe option for Cortex-M3, M4 and M7 cores.
This however has the disadvantage of only resetting the core, all peripherals
-are unaffected. A solution would be to use a @code{reset-init} event handler to manually reset
-the peripherals.
+are unaffected. A solution would be to use a @code{reset-init} event handler
+to manually reset the peripherals.
@xref{targetevents,,Target Events}.
+
+Cortex-M0, M0+ and M1 do not support @option{vectreset}, use @option{sysresetreq}
+instead.
@end deffn
@subsection ARMv8-A specific commands