NOR: lpc2000 Add support for LPC84x devices

[openocd.git] / doc / openocd.texi

diff --git a/doc/openocd.texi b/doc/openocd.texi
index 11ee93e2b62a8e99216a2dce2a14f3e412ac2772..4b1a5de3d75f0c3994884d2a972a0c5f76836d70 100644 (file)
--- a/doc/openocd.texi
+++ b/doc/openocd.texi
@@ -3458,6 +3458,7 @@ How long (in milliseconds) OpenOCD should wait after deasserting
 nTRST (active-low JTAG TAP reset) before starting new JTAG operations.
 @end deffn
 
+@anchor {reset_config}
 @deffn {Command} reset_config mode_flag ...
 This command displays or modifies the reset configuration
 of your combination of JTAG board and target in target
@@ -5346,12 +5347,12 @@ since the alternate function must be enabled on the GPIO pin
 CS1/CS2 is routed to on the given SoC.
 
 @example
-flash bank $_FLASHNAME ath79 0 0 0 0 $_TARGETNAME
+flash bank $_FLASHNAME ath79 0xbf000000 0 0 0 $_TARGETNAME
 
 # When using multiple chipselects the base should be different for each,
 # otherwise the write_image command is not able to distinguish the
 # banks.
-flash bank flash0 ath79 0x00000000 0 0 0 $_TARGETNAME cs0
+flash bank flash0 ath79 0xbf000000 0 0 0 $_TARGETNAME cs0
 flash bank flash1 ath79 0x10000000 0 0 0 $_TARGETNAME cs1
 flash bank flash2 ath79 0x20000000 0 0 0 $_TARGETNAME cs2
 @end example
@@ -5899,8 +5900,8 @@ Command disables watchdog timer.
 @deffn {Flash Driver} lpc2000
 This is the driver to support internal flash of all members of the
 LPC11(x)00 and LPC1300 microcontroller families and most members of
-the LPC800, LPC1500, LPC1700, LPC1800, LPC2000, LPC4000 and LPC54100
-microcontroller families from NXP.
+the LPC800, LPC1500, LPC1700, LPC1800, LPC2000, LPC4000, LPC54100,
+LPC8Nxx and NHS31xx microcontroller families from NXP.
 
 @quotation Note
 There are LPC2000 devices which are not supported by the @var{lpc2000}
@@ -5909,7 +5910,7 @@ The LPC2888 is supported by the @var{lpc288x} driver.
 The LPC29xx family is supported by the @var{lpc2900} driver.
 @end quotation
 
-The @var{lpc2000} driver defines two mandatory and one optional parameters,
+The @var{lpc2000} driver defines two mandatory and two optional parameters,
 which must appear in the following order:
 
 @itemize
@@ -5925,7 +5926,7 @@ LPC43x[2357])
 @option{lpc54100} (LPC541xx)
 @option{lpc4000} (LPC40xx)
 or @option{auto} - automatically detects flash variant and size for LPC11(x)00,
-LPC8xx, LPC13xx, LPC17xx and LPC40xx
+LPC8xx, LPC13xx, LPC17xx, LPC40xx, LPC8Nxx and NHS31xx
 @item @var{clock_kHz} ... the frequency, in kiloHertz,
 at which the core is running
 @item @option{calc_checksum} ... optional (but you probably want to provide this!),
@@ -5936,6 +5937,8 @@ table, the boot ROM will almost certainly ignore your flash image.
 However, if you do provide it,
 with most tool chains @command{verify_image} will fail.
 @end quotation
+@item @option{iap_entry} ... optional telling the driver to use a different
+ROM IAP entry point.
 @end itemize
 
 LPC flashes don't require the chip and bus width to be specified.
@@ -6890,6 +6893,17 @@ the flash clock.
 @end deffn
 @end deffn
 
+@deffn {Flash Driver} w600
+W60x series Wi-Fi SoC from WinnerMicro
+are designed with ARM Cortex-M3 and have 1M Byte QFLASH inside.
+The @var{w600} driver uses the @var{target} parameter to select the
+correct bank config.
+
+@example
+flash bank $_FLASHNAME w600 0x08000000 0 0 0 $_TARGETNAMEs
+@end example
+@end deffn
+
 @deffn {Flash Driver} xmc1xxx
 All members of the XMC1xxx microcontroller family from Infineon.
 This driver does not require the chip and bus width to be specified.
@@ -8994,19 +9008,23 @@ must also be explicitly enabled.
 This finishes by listing the current vector catch configuration.
 @end deffn
 
-@deffn Command {cortex_m reset_config} (@option{srst}|@option{sysresetreq}|@option{vectreset})
-Control reset handling. The default @option{srst} is to use srst if fitted,
-otherwise fallback to @option{vectreset}.
+@deffn Command {cortex_m reset_config} (@option{sysresetreq}|@option{vectreset})
+Control reset handling if hardware srst is not fitted
+@xref{reset_config,,reset_config}.
+
 @itemize @minus
-@item @option{srst} use hardware srst if fitted otherwise fallback to @option{vectreset}.
-@item @option{sysresetreq} use NVIC SYSRESETREQ to reset system.
-@item @option{vectreset} use NVIC VECTRESET to reset system.
+@item @option{sysresetreq} use AIRCR SYSRESETREQ to reset system.
+@item @option{vectreset} use AIRCR VECTRESET to reset system (default).
 @end itemize
-Using @option{vectreset} is a safe option for all current Cortex-M cores.
+
+Using @option{vectreset} is a safe option for Cortex-M3, M4 and M7 cores.
 This however has the disadvantage of only resetting the core, all peripherals
-are unaffected. A solution would be to use a @code{reset-init} event handler to manually reset
-the peripherals.
+are unaffected. A solution would be to use a @code{reset-init} event handler
+to manually reset the peripherals.
 @xref{targetevents,,Target Events}.
+
+Cortex-M0, M0+ and M1 do not support @option{vectreset}, use @option{sysresetreq}
+instead.
 @end deffn
 
 @subsection ARMv8-A specific commands