@section OpenOCD User's Forum
-There is an OpenOCD forum (phpBB) hosted by SparkFun:
+There is an OpenOCD forum (phpBB) hosted by SparkFun,
+which might be helpful to you. Note that if you want
+anything to come to the attention of developers, you
+should post it to the OpenOCD Developer Mailing List
+instead of this forum.
@uref{http://forum.sparkfun.com/viewforum.php?f=18}
@uref{https://lists.berlios.de/mailman/listinfo/openocd-development}
Discuss and submit patches to this list.
-The @file{PATCHES} file contains basic information about how
+The @file{PATCHES.txt} file contains basic information about how
to prepare patches.
When the OpenOCD server process starts up, it enters a
@emph{configuration stage} which is the only time that
certain commands, @emph{configuration commands}, may be issued.
+Normally, configuration commands are only available
+inside startup scripts.
+
In this manual, the definition of a configuration command is
presented as a @emph{Config Command}, not as a @emph{Command}
which may be issued interactively.
+The runtime @command{help} command also highlights configuration
+commands, and those which may be issued at any time.
Those configuration commands include declaration of TAPs,
flash banks,
The default behaviour if no option given is @option{separate},
indicating everything behaves normally.
@option{srst_pulls_trst} states that the
-test logic is reset together with the reset of the system (e.g. Philips
+test logic is reset together with the reset of the system (e.g. NXP
LPC2000, "broken" board layout), @option{trst_pulls_srst} says that
the system is reset together with the test logic (only hypothetical, I
haven't seen hardware with such a bug, and can be worked around).
Exits the current telnet session.
@end deffn
-@c note EXTREMELY ANNOYING word wrap at column 75
-@c even when lines are e.g. 100+ columns ...
-@c coded in startup.tcl
@deffn {Command} help [string]
With no parameters, prints help text for all commands.
Otherwise, prints each helptext containing @var{string}.
Not every command provides helptext.
+
+Configuration commands, and commands valid at any time, are
+explicitly noted in parenthesis.
+In most cases, no such restriction is listed; this indicates commands
+which are only available after the configuration stage has completed.
@end deffn
@deffn Command sleep msec [@option{busy}]
They are available in addition to the ARM commands,
and any other core-specific commands that may be available.
-@deffn Command {arm7_9 dbgrq} (@option{enable}|@option{disable})
-Control use of the EmbeddedIce DBGRQ signal to force entry into debug mode,
-instead of breakpoints. This should be
-safe for all but ARM7TDMI--S cores (like Philips LPC).
+@deffn Command {arm7_9 dbgrq} [@option{enable}|@option{disable}]
+Displays the value of the flag controlling use of the
+the EmbeddedIce DBGRQ signal to force entry into debug mode,
+instead of breakpoints.
+If a boolean parameter is provided, first assigns that flag.
+
+This should be
+safe for all but ARM7TDMI-S cores (like NXP LPC).
This feature is enabled by default on most ARM9 cores,
including ARM9TDMI, ARM920T, and ARM926EJ-S.
@end deffn
-@deffn Command {arm7_9 dcc_downloads} (@option{enable}|@option{disable})
+@deffn Command {arm7_9 dcc_downloads} [@option{enable}|@option{disable}]
@cindex DCC
-Control the use of the debug communications channel (DCC) to write larger (>128 byte)
-amounts of memory. DCC downloads offer a huge speed increase, but might be
+Displays the value of the flag controlling use of the debug communications
+channel (DCC) to write larger (>128 byte) amounts of memory.
+If a boolean parameter is provided, first assigns that flag.
+
+DCC downloads offer a huge speed increase, but might be
unsafe, especially with targets running at very low speeds. This command was introduced
with OpenOCD rev. 60, and requires a few bytes of working area.
@end deffn
@anchor{arm7_9 fast_memory_access}
-@deffn Command {arm7_9 fast_memory_access} (@option{enable}|@option{disable})
-Enable or disable memory writes and reads that don't check completion of
-the operation. This provides a huge speed increase, especially with USB JTAG
+@deffn Command {arm7_9 fast_memory_access} [@option{enable}|@option{disable}]
+Displays the value of the flag controlling use of memory writes and reads
+that don't check completion of the operation.
+If a boolean parameter is provided, first assigns that flag.
+
+This provides a huge speed increase, especially with USB JTAG
cables (FT2232), but might be unsafe if used with targets running at very low
speeds, like the 32kHz startup clock of an AT91RM9200.
@end deffn
based on the ARM7TDMI-S integer core.
They are available in addition to the ARM and ARM7/ARM9 commands.
-@deffn Command {arm720t cp15} regnum [value]
-Display cp15 register @var{regnum};
+@deffn Command {arm720t cp15} opcode [value]
+@emph{DEPRECATED -- avoid using this.
+Use the @command{arm mrc} or @command{arm mcr} commands instead.}
+
+Display cp15 register returned by the ARM instruction @var{opcode};
else if a @var{value} is provided, that value is written to that register.
+The @var{opcode} should be the value of either an MRC or MCR instruction.
@end deffn
@subsection ARM9 specific commands
@deffn Command {arm920t cp15} regnum [value]
Display cp15 register @var{regnum};
else if a @var{value} is provided, that value is written to that register.
+This uses "physical access" and the register number is as
+shown in bits 38..33 of table 9-9 in the ARM920T TRM.
+(Not all registers can be written.)
@end deffn
@deffn Command {arm920t cp15i} opcode [value [address]]
-Interpreted access using cp15 @var{opcode}.
+@emph{DEPRECATED -- avoid using this.
+Use the @command{arm mrc} or @command{arm mcr} commands instead.}
+
+Interpreted access using ARM instruction @var{opcode}, which should
+be the value of either an MRC or MCR instruction
+(as shown tables 9-11, 9-12, and 9-13 in the ARM920T TRM).
If no @var{value} is provided, the result is displayed.
Else if that value is written using the specified @var{address},
-or using zero if no other address is not provided.
+or using zero if no other address is provided.
@end deffn
@deffn Command {arm920t read_cache} filename
@deffn Command {arm966e cp15} regnum [value]
Display cp15 register @var{regnum};
else if a @var{value} is provided, that value is written to that register.
+The six bit @var{regnum} values are bits 37..32 from table 7-2 of the
+ARM966E-S TRM.
+There is no current control over bits 31..30 from that table,
+as required for BIST support.
@end deffn
@subsection XScale specific commands
Changes the address used for the specified target's debug handler.
@end deffn
-@deffn Command {xscale dcache} (@option{enable}|@option{disable})
+@deffn Command {xscale dcache} [@option{enable}|@option{disable}]
Enables or disable the CPU's data cache.
@end deffn
Dumps the raw contents of the trace buffer to @file{filename}.
@end deffn
-@deffn Command {xscale icache} (@option{enable}|@option{disable})
+@deffn Command {xscale icache} [@option{enable}|@option{disable}]
Enables or disable the CPU's instruction cache.
@end deffn
-@deffn Command {xscale mmu} (@option{enable}|@option{disable})
+@deffn Command {xscale mmu} [@option{enable}|@option{disable}]
Enables or disable the CPU's memory management unit.
@end deffn
-@deffn Command {xscale trace_buffer} (@option{enable}|@option{disable}) [@option{fill} [n] | @option{wrap}]
-Enables or disables the trace buffer,
-and controls how it is emptied.
+@deffn Command {xscale trace_buffer} [@option{enable}|@option{disable} [@option{fill} [n] | @option{wrap}]]
+Displays the trace buffer status, after optionally
+enabling or disabling the trace buffer
+and modifying how it is emptied.
@end deffn
@deffn Command {xscale trace_image} filename [offset [type]]
@end deffn
@anchor{xscale vector_table}
-@deffn Command {xscale vector_table} [<low|high> <index> <value>]
+@deffn Command {xscale vector_table} [(@option{low}|@option{high}) index value]
@cindex vector_table
Set an entry in the mini-IC vector table. There are two tables: one for
@subsection ARM11 specific commands
@cindex ARM11
-@deffn Command {arm11 memwrite burst} [value]
+@deffn Command {arm11 memwrite burst} [@option{enable}|@option{disable}]
Displays the value of the memwrite burst-enable flag,
-which is enabled by default. Burst writes are only used
-for memory writes larger than 1 word. Single word writes
-are likely to be from reset init scripts and those writes
-are often to non-memory locations which could easily have
-many wait states, which could easily break burst writes.
-If @var{value} is defined, first assigns that.
+which is enabled by default.
+If a boolean parameter is provided, first assigns that flag.
+Burst writes are only used for memory writes larger than 1 word.
+They improve performance by assuming that the CPU has read each data
+word over JTAG and completed its write before the next word arrives,
+instead of polling for a status flag to verify that completion.
+This is usually safe, because JTAG runs much slower than the CPU.
@end deffn
-@deffn Command {arm11 memwrite error_fatal} [value]
+@deffn Command {arm11 memwrite error_fatal} [@option{enable}|@option{disable}]
Displays the value of the memwrite error_fatal flag,
which is enabled by default.
-If @var{value} is defined, first assigns that.
+If a boolean parameter is provided, first assigns that flag.
+When set, certain memory write errors cause earlier transfer termination.
@end deffn
-@deffn Command {arm11 step_irq_enable} [value]
+@deffn Command {arm11 step_irq_enable} [@option{enable}|@option{disable}]
Displays the value of the flag controlling whether
IRQs are enabled during single stepping;
they are disabled by default.
-If @var{value} is defined, first assigns that.
+If a boolean parameter is provided, first assigns that.
@end deffn
@deffn Command {arm11 vcr} [value]
included on Cortex-M3 and Cortex-A8 systems.
They are available in addition to other core-specific commands that may be available.
-@deffn Command {dap info} [num]
-Displays dap info for ap @var{num}, defaulting to the currently selected AP.
+@deffn Command {dap apid} [num]
+Displays ID register from AP @var{num},
+defaulting to the currently selected AP.
@end deffn
@deffn Command {dap apsel} [num]
Select AP @var{num}, defaulting to 0.
@end deffn
-@deffn Command {dap apid} [num]
-Displays id register from AP @var{num},
+@deffn Command {dap baseaddr} [num]
+Displays debug base address from MEM-AP @var{num},
defaulting to the currently selected AP.
@end deffn
-@deffn Command {dap baseaddr} [num]
-Displays debug base address from AP @var{num},
+@deffn Command {dap info} [num]
+Displays the ROM table for MEM-AP @var{num},
defaulting to the currently selected AP.
@end deffn
@deffn Command {dap memaccess} [value]
-Displays the number of extra tck for mem-ap memory bus access [0-255].
+Displays the number of extra tck cycles in the JTAG idle to use for MEM-AP
+memory bus access [0-255], giving additional time to respond to reads.
If @var{value} is defined, first assigns that.
@end deffn
Code Review / openocd.git / blobdiff