If you disable all access through TCP/IP, you will need to
use the command line @option{-pipe} option.
-@deffn {Command} gdb_port (number)
+@deffn {Command} gdb_port [number]
@cindex GDB server
Specify or query the first port used for incoming GDB connections.
The GDB port for the
first target will be gdb_port, the second target will listen on gdb_port + 1, and so on.
When not specified during the configuration stage,
the port @var{number} defaults to 3333.
-When specified as zero, this port is not activated.
+When specified as zero, GDB remote access ports are not activated.
@end deffn
-@deffn {Command} tcl_port (number)
+@deffn {Command} tcl_port [number]
Specify or query the port used for a simplified RPC
connection that can be used by clients to issue TCL commands and get the
output from the Tcl engine.
When specified as zero, this port is not activated.
@end deffn
-@deffn {Command} telnet_port (number)
+@deffn {Command} telnet_port [number]
Specify or query the
port on which to listen for incoming telnet connections.
This port is intended for interaction with one human through TCL commands.
Gateworks GW16012 JTAG programmer.
This has one driver-specific command:
-@deffn {Config Command} {parport_port} number
-Specifies either the address of the I/O port (default: 0x378 for LPT1) or
-the number of the @file{/dev/parport} device.
+@deffn {Config Command} {parport_port} [port_number]
+Display either the address of the I/O port
+(default: 0x378 for LPT1) or the number of the @file{/dev/parport} device.
+If a parameter is provided, first switch to use that port.
+This is a write-once setting.
@end deffn
@end deffn
before initializing the JTAG scan chain:
@deffn {Config Command} {parport_cable} name
-The layout of the parallel port cable used to connect to the target.
+Set the layout of the parallel port cable used to connect to the target.
+This is a write-once setting.
Currently valid cable @var{name} values include:
@itemize @minus
@end itemize
@end deffn
-@deffn {Config Command} {parport_port} number
-Either the address of the I/O port (default: 0x378 for LPT1) or the number of
-the @file{/dev/parport} device
+@deffn {Config Command} {parport_port} [port_number]
+Display either the address of the I/O port
+(default: 0x378 for LPT1) or the number of the @file{/dev/parport} device.
+If a parameter is provided, first switch to use that port.
+This is a write-once setting.
When using PPDEV to access the parallel port, use the number of the parallel port:
@option{parport_port 0} (the default). If @option{parport_port 0x378} is specified
@end quotation
@end deffn
-@deffn {Config Command} {parport_write_on_exit} (on|off)
+@deffn {Config Command} {parport_write_on_exit} (@option{on}|@option{off})
This will configure the parallel driver to write a known
-cable-specific value to the parallel interface on exiting OpenOCD
+cable-specific value to the parallel interface on exiting OpenOCD.
@end deffn
For example, the interface configuration file for a
-classic ``Wiggler'' cable might look something like this:
+classic ``Wiggler'' cable on LPT2 might look something like this:
@example
interface parport
-parport_port 0xc8b8
+parport_port 0x278
parport_cable wiggler
@end example
@end deffn
@deffn {Interface Driver} {presto}
ASIX PRESTO USB JTAG programmer.
-@c command: presto_serial str
-@c sets serial number
+@deffn {Config Command} {presto_serial} serial_string
+Configures the USB serial number of the Presto device to use.
+@end deffn
@end deffn
@deffn {Interface Driver} {rlink}
@itemize @bullet
@item @var{name} ... may be used to reference the flash bank
-in other flash commands.
+in other flash commands. A number is also available.
@item @var{driver} ... identifies the controller driver
associated with the flash bank being declared.
This is usually @code{cfi} for external flash, or else
@command{flash erase_sector} or @command{flash erase_address} commands.
@deffn Command {at91sam7 gpnvm} bitnum (@option{set}|@option{clear})
-Set or clear a ``General Purpose Non-Volatle Memory'' (GPNVM)
+Set or clear a ``General Purpose Non-Volatile Memory'' (GPNVM)
bit for the processor. Each processor has a number of such bits,
used for controlling features such as brownout detection (so they
are not truly general purpose).
plus some additional configuration that's done after
OpenOCD has initialized.
-@deffn {Config Command} {nand device} name controller target [configparams...]
+@deffn {Config Command} {nand device} name driver target [configparams...]
Declares a NAND device, which can be read and written to
after it has been configured through @command{nand probe}.
In OpenOCD, devices are single chips; this is unlike some
@itemize @bullet
@item @var{name} ... may be used to reference the NAND bank
-in other commands.
-@item @var{controller} ... identifies the controller driver
+in most other NAND commands. A number is also available.
+@item @var{driver} ... identifies the NAND controller driver
associated with the NAND device being declared.
@xref{NAND Driver List}.
@item @var{target} ... names the target used when issuing
holds one of the following values:
@itemize @bullet
-@item @b{winxx} Built using Microsoft Visual Studio
-@item @b{linux} Linux is the underlying operating sytem
-@item @b{darwin} Darwin (mac-os) is the underlying operating sytem.
@item @b{cygwin} Running under Cygwin
+@item @b{darwin} Darwin (Mac-OS) is the underlying operating sytem.
+@item @b{freebsd} Running under FreeBSD
+@item @b{linux} Linux is the underlying operating sytem
@item @b{mingw32} Running under MingW32
+@item @b{winxx} Built using Microsoft Visual Studio
@item @b{other} Unknown, none of the above.
@end itemize
Code Review / openocd.git / blobdiff