#
# Texas Instruments DaVinci family:  TMS320DM355
#
if { [info exists CHIPNAME] } {
   set  _CHIPNAME $CHIPNAME
} else {
   set  _CHIPNAME dm355
}
if { [info exists ENDIAN] } {
   set  _ENDIAN $ENDIAN
} else {
   set  _ENDIAN little
}

#
# For now, expect EMU0/EMU1 jumpered LOW (not TI's default) so ARM and ETB
# are enabled without making ICEpick route ARM and ETB into the JTAG chain.
#
# Also note:  when running without RTCK before the PLLs are set up, you
# may need to slow the JTAG clock down quite a lot (under 2 MHz).
#

# Subsidiary TAP: ARM ETB11, with scan chain for 4K of ETM trace buffer
if { [info exists ETB_TAPID ] } {
   set _ETB_TAPID $ETB_TAPID
} else {
   set _ETB_TAPID 0x2b900f0f
}
jtag newtap $_CHIPNAME etb -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_ETB_TAPID

# Subsidiary TAP: ARM926ejs with scan chains for ARM Debug, EmbeddedICE-RT, ETM.
if { [info exists CPU_TAPID ] } {
   set _CPU_TAPID $CPU_TAPID
} else {
   set _CPU_TAPID 0x07926001
}
jtag newtap $_CHIPNAME arm -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPU_TAPID

# Primary TAP: ICEpick (JTAG route controller) and boundary scan
if { [info exists JRC_TAPID ] } {
   set _JRC_TAPID $JRC_TAPID
} else {
   set _JRC_TAPID 0x0b73b02f
}
jtag newtap $_CHIPNAME jrc -irlen 6 -ircapture 0x1 -irmask 0x3f -expected-id $_JRC_TAPID

################

# various symbol definitions, to avoid hard-wiring addresses
# and enable some sharing of DaVinci-family utility code
global dm355
set dm355 [ dict create ]

# Physical addresses for controllers and memory
# (Some of these are valid for many DaVinci family chips)
dict set dm355 sram0		0x00010000
dict set dm355 sram1		0x00014000
dict set dm355 sysbase		0x01c40000
dict set dm355 pllc1		0x01c40800
dict set dm355 pllc2		0x01c40c00
dict set dm355 psc		0x01c41000
dict set dm355 gpio		0x01c67000
dict set dm355 a_emif		0x01e10000
dict set dm355 a_emif_cs0	0x02000000
dict set dm355 a_emif_cs1	0x04000000
dict set dm355 ddr_emif		0x20000000
dict set dm355 ddr		0x80000000

source [find target/davinci.cfg]

################
# GDB target:  the ARM, using SRAM1 for scratch.  SRAM0 (also 16K)
# and the ETB memory (4K) are other options, while trace is unused.
set _TARGETNAME $_CHIPNAME.arm

target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNAME

# NOTE that work-area-virt presumes a Linux 2.6.30-rc2+ kernel,
# and that the work area is used only with a kernel mmu context ...
$_TARGETNAME configure \
	-work-area-virt [expr 0xfffe0000 + 0x4000] \
	-work-area-phys [dict get $dm355 sram1] \
	-work-area-size 0x4000 \
	-work-area-backup 0

arm7_9 dbgrq enable
arm7_9 fast_memory_access enable
arm7_9 dcc_downloads enable

# trace setup
etm config $_TARGETNAME 16 normal full etb
etb config $_TARGETNAME $_CHIPNAME.etb