cfg: allow stm32discovery parameter override
[openocd.git] / tcl / target / stm32f2x.cfg
1 # script for stm32f2x family
2
3 if { [info exists CHIPNAME] } {
4 set _CHIPNAME $CHIPNAME
5 } else {
6 set _CHIPNAME stm32f2x
7 }
8
9 if { [info exists ENDIAN] } {
10 set _ENDIAN $ENDIAN
11 } else {
12 set _ENDIAN little
13 }
14
15 # Work-area is a space in RAM used for flash programming
16 # By default use 64kB
17 if { [info exists WORKAREASIZE] } {
18 set _WORKAREASIZE $WORKAREASIZE
19 } else {
20 set _WORKAREASIZE 0x10000
21 }
22
23 # JTAG speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so use F_JTAG = 1MHz
24 #
25 # Since we may be running of an RC oscilator, we crank down the speed a
26 # bit more to be on the safe side. Perhaps superstition, but if are
27 # running off a crystal, we can run closer to the limit. Note
28 # that there can be a pretty wide band where things are more or less stable.
29 adapter_khz 1000
30
31 adapter_nsrst_delay 100
32 jtag_ntrst_delay 100
33
34 #jtag scan chain
35 if { [info exists CPUTAPID] } {
36 set _CPUTAPID $CPUTAPID
37 } else {
38 # See STM Document RM0033
39 # Section 32.6.3 - corresponds to Cortex-M3 r2p0
40 set _CPUTAPID 0x4ba00477
41 }
42 jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
43
44 if { [info exists BSTAPID] } {
45 set _BSTAPID $BSTAPID
46 } else {
47 # See STM Document RM0033
48 # Section 32.6.2
49 #
50 set _BSTAPID 0x06411041
51 }
52 jtag newtap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID
53
54 set _TARGETNAME $_CHIPNAME.cpu
55 target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME
56
57 $_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
58
59 set _FLASHNAME $_CHIPNAME.flash
60 flash bank $_FLASHNAME stm32f2x 0 0 0 0 $_TARGETNAME
61
62 # if srst is not fitted use SYSRESETREQ to
63 # perform a soft reset
64 cortex_m3 reset_config sysresetreq

Linking to existing account procedure

If you already have an account and want to add another login method you MUST first sign in with your existing account and then change URL to read https://review.openocd.org/login/?link to get to this page again but this time it'll work for linking. Thank you.

SSH host keys fingerprints

1024 SHA256:YKx8b7u5ZWdcbp7/4AeXNaqElP49m6QrwfXaqQGJAOk gerrit-code-review@openocd.zylin.com (DSA)
384 SHA256:jHIbSQa4REvwCFG4cq5LBlBLxmxSqelQPem/EXIrxjk gerrit-code-review@openocd.org (ECDSA)
521 SHA256:UAOPYkU9Fjtcao0Ul/Rrlnj/OsQvt+pgdYSZ4jOYdgs gerrit-code-review@openocd.org (ECDSA)
256 SHA256:A13M5QlnozFOvTllybRZH6vm7iSt0XLxbA48yfc2yfY gerrit-code-review@openocd.org (ECDSA)
256 SHA256:spYMBqEYoAOtK7yZBrcwE8ZpYt6b68Cfh9yEVetvbXg gerrit-code-review@openocd.org (ED25519)
+--[ED25519 256]--+
|=..              |
|+o..   .         |
|*.o   . .        |
|+B . . .         |
|Bo. = o S        |
|Oo.+ + =         |
|oB=.* = . o      |
| =+=.+   + E     |
|. .=o   . o      |
+----[SHA256]-----+
2048 SHA256:0Onrb7/PHjpo6iVZ7xQX2riKN83FJ3KGU0TvI0TaFG4 gerrit-code-review@openocd.zylin.com (RSA)