tcl/target/lpc1xxx.cfg

   1 # Main file for NXP LPC1xxx/LPC40xx series Cortex-M0/0+/3/4F parts
   2 #
   3 # !!!!!!
   4 #
   5 # This file should not be included directly, rather by the lpc11xx.cfg,
   6 # lpc13xx.cfg, lpc17xx.cfg, etc. which set the needed variables to the
   7 # appropriate values.
   8 #
   9 # !!!!!!
  10
  11 # LPC8xx chips support only SWD transport.
  12 # LPC11xx chips support only SWD transport.
  13 # LPC12xx chips support only SWD transport.
  14 # LPC11Uxx chips support only SWD transports.
  15 # LPC13xx chips support only SWD transports.
  16 # LPC17xx chips support both JTAG and SWD transports.
  17 # LPC40xx chips support both JTAG and SWD transports.
  18 # Adapt based on what transport is active.
  19 source [find target/swj-dp.tcl]
  20
  21 if { [info exists CHIPNAME] } {
  22         set _CHIPNAME $CHIPNAME
  23 } else {
  24         error "CHIPNAME not set. Please do not include lpc1xxx.cfg directly, but the specific chip configuration file (lpc11xx.cfg, lpc13xx.cfg, lpc17xx.cfg, etc)."
  25 }
  26
  27 if { [info exists CHIPSERIES] } {
  28         # Validate chip series is supported
  29         if { $CHIPSERIES != "lpc800" && $CHIPSERIES != "lpc1100" && $CHIPSERIES != "lpc1200" && $CHIPSERIES != "lpc1300" && $CHIPSERIES != "lpc1700"  && $CHIPSERIES != "lpc4000" } {
  30                 error "Unsupported LPC1xxx chip series specified."
  31         }
  32         set _CHIPSERIES $CHIPSERIES
  33 } else {
  34         error "CHIPSERIES not set. Please do not include lpc1xxx.cfg directly, but the specific chip configuration file (lpc11xx.cfg, lpc13xx.cfg, lpc17xx.cfg, etc)."
  35 }
  36
  37 # After reset, the chip is clocked by an internal RC oscillator.
  38 # When board-specific code (reset-init handler or device firmware)
  39 # configures another oscillator and/or PLL0, set CCLK to match; if
  40 # you don't, then flash erase and write operations may misbehave.
  41 # (The ROM code doing those updates cares about core clock speed...)
  42 # CCLK is the core clock frequency in KHz
  43 if { [info exists CCLK] } {
  44         # Allow user override
  45         set _CCLK $CCLK
  46 } else {
  47         # LPC8xx/LPC11xx/LPC12xx/LPC13xx use a 12MHz one, LPC17xx uses a 4MHz one(except for LPC177x/8x,LPC407x/8x)
  48         if { $_CHIPSERIES == "lpc800" || $_CHIPSERIES == "lpc1100" || $_CHIPSERIES == "lpc1200" || $_CHIPSERIES == "lpc1300" } {
  49                 set _CCLK 12000
  50         } elseif { $_CHIPSERIES == "lpc1700" || $_CHIPSERIES == "lpc4000" } {
  51                 set _CCLK 4000
  52         }
  53 }
  54
  55 if { [info exists CPUTAPID] } {
  56         # Allow user override
  57         set _CPUTAPID $CPUTAPID
  58 } else {
  59         # LPC8xx/LPC11xx/LPC12xx use a Cortex-M0/M0+ core, LPC13xx/LPC17xx use a Cortex-M3 core, LPC40xx use a Cortex-M4F core.
  60         if { $_CHIPSERIES == "lpc800" || $_CHIPSERIES == "lpc1100" || $_CHIPSERIES == "lpc1200" } {
  61                 set _CPUTAPID 0x0bb11477
  62         } elseif { $_CHIPSERIES == "lpc1300" || $_CHIPSERIES == "lpc1700" || $_CHIPSERIES == "lpc4000" } {
  63                 if { [using_jtag] } {
  64                         set _CPUTAPID 0x4ba00477
  65                 } {
  66                         set _CPUTAPID 0x2ba01477
  67                 }
  68         }
  69 }
  70
  71 if { [info exists WORKAREASIZE] } {
  72         set _WORKAREASIZE $WORKAREASIZE
  73 } else {
  74         error "WORKAREASIZE is not set. The $CHIPNAME part is available in several Flash and RAM size configurations. Please set WORKAREASIZE."
  75 }
  76
  77 swj_newdap $_CHIPNAME cpu -irlen 4 -expected-id $_CPUTAPID
  78 dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
  79
  80 set _TARGETNAME $_CHIPNAME.cpu
  81 target create $_TARGETNAME cortex_m -dap $_CHIPNAME.dap
  82
  83 # The LPC11xx devices have 2/4/8kB of SRAM in the ARMv7-M "Code" area (at 0x10000000)
  84 # The LPC12xx devices have 4/8kB of SRAM in the ARMv7-M "Code" area (at 0x10000000)
  85 # The LPC11Uxx devices have 4/6/8kB of SRAM in the ARMv7-M "Code" area (at 0x10000000)
  86 # The LPC13xx devices have 4/8kB of SRAM in the ARMv7-M "Code" area (at 0x10000000)
  87 # The LPC17xx devices have 8/16/32/64kB of SRAM in the ARMv7-M "Code" area (at 0x10000000)
  88 # The LPC40xx devices have 16/32/64kB of SRAM in the ARMv7-ME "Code" area (at 0x10000000)
  89 $_TARGETNAME configure -work-area-phys 0x10000000 -work-area-size $_WORKAREASIZE
  90
  91 # The LPC11xx devies have 8/16/24/32/48/56/64kB of flash memory (at 0x00000000)
  92 # The LPC12xx devies have 32/48/64/80/96/128kB of flash memory (at 0x00000000)
  93 # The LPC11Uxx devies have 16/24/32/40/48/64/96/128kB of flash memory (at 0x00000000)
  94 # The LPC13xx devies have 8/16/32kB of flash memory (at 0x00000000)
  95 # The LPC17xx devies have 32/64/128/256/512kB of flash memory (at 0x00000000)
  96 # The LPC40xx devies have 64/128/256/512kB of flash memory (at 0x00000000)
  97 #
  98 # All are compatible with the "lpc1700" variant of the LPC2000 flash driver
  99 # (same cmd51 destination boundary alignment, and all three support 256 byte
 100 # transfers).
 101 #
 102 # flash bank <name> lpc2000 <base> <size> 0 0 <target#> <variant> <clock> [calc checksum] [iap entry]
 103 set _IAP_ENTRY 0
 104 if { [info exists IAP_ENTRY] } {
 105         set _IAP_ENTRY $IAP_ENTRY
 106 }
 107 set _FLASHNAME $_CHIPNAME.flash
 108 flash bank $_FLASHNAME lpc2000 0x0 0 0 0 $_TARGETNAME \
 109         auto $_CCLK calc_checksum $_IAP_ENTRY
 110
 111 if { $_CHIPSERIES == "lpc800" || $_CHIPSERIES == "lpc1100" || $_CHIPSERIES == "lpc1200" || $_CHIPSERIES == "lpc1300" } {
 112         # Do not remap 0x0000-0x0200 to anything but the flash (i.e. select
 113         # "User Flash Mode" where interrupt vectors are _not_ remapped,
 114         # and reside in flash instead).
 115         #
 116         # Table 8. System memory remap register (SYSMEMREMAP, address 0x4004 8000) bit description
 117         # Bit Symbol Value Description
 118         # 1:0 MAP          System memory remap
 119         #            0x0   Boot Loader Mode. Interrupt vectors are re-mapped to Boot ROM.
 120         #            0x1   User RAM Mode. Interrupt vectors are re-mapped to Static RAM.
 121         #            0x2   User Flash Mode. Interrupt vectors are not re-mapped and reside in Flash.
 122         # 31:2 -     -     Reserved.
 123         $_TARGETNAME configure -event reset-init {
 124                 mww 0x40048000 0x02
 125         }
 126 } elseif { $_CHIPSERIES == "lpc1700" || $_CHIPSERIES == "lpc4000" } {
 127         # Do not remap 0x0000-0x0020 to anything but the flash (i.e. select
 128         # "User Flash Mode" where interrupt vectors are _not_ remapped,
 129         # and reside in flash instead).
 130         #
 131         # See Table 612. Memory Mapping Control register (MEMMAP - 0x400F C040) bit description
 132         # Bit Symbol Value Description Reset
 133         # value
 134         # 0 MAP Memory map control. 0
 135         # 0 Boot mode. A portion of the Boot ROM is mapped to address 0.
 136         # 1 User mode. The on-chip Flash memory is mapped to address 0.
 137         # 31:1 - Reserved. The value read from a reserved bit is not defined. NA
 138         #
 139         # http://ics.nxp.com/support/documents/microcontrollers/?scope=LPC1768&type=user
 140         $_TARGETNAME configure -event reset-init {
 141                 mww 0x400FC040 0x01
 142         }
 143 }
 144
 145 # Run with *real slow* clock by default since the
 146 # boot rom could have been playing with the PLL, so
 147 # we have no idea what clock the target is running at.
 148 adapter_khz 10
 149
 150 # delays on reset lines
 151 adapter_nsrst_delay 200
 152 if {[using_jtag]} {
 153  jtag_ntrst_delay 200
 154 }
 155
 156 # LPC8xx (Cortex-M0+ core) support SYSRESETREQ
 157 # LPC11xx/LPC12xx (Cortex-M0 core) support SYSRESETREQ
 158 # LPC13xx/LPC17xx (Cortex-M3 core) support SYSRESETREQ
 159 # LPC40xx (Cortex-M4F core) support SYSRESETREQ
 160 if {![using_hla]} {
 161     # if srst is not fitted use SYSRESETREQ to
 162     # perform a soft reset
 163     cortex_m reset_config sysresetreq
 164 }