X-Git-Url: https://review.openocd.org/gitweb?a=blobdiff_plain;f=tcl%2Ftarget%2Fstm32f4x.cfg;h=7205c461486e4f152348a8bceb21dc6afa40a120;hb=08cdb58f05d0229b8ecdc9aa2c9e805d9f0f77dd;hp=a7ec5eab3e18e5f59c3724c42520ed614cd933a9;hpb=9c4d2946548f72d77f103b978ab30501d5953f04;p=openocd.git

diff --git a/tcl/target/stm32f4x.cfg b/tcl/target/stm32f4x.cfg
index a7ec5eab3e..7205c46148 100644
--- a/tcl/target/stm32f4x.cfg
+++ b/tcl/target/stm32f4x.cfg
@@ -4,6 +4,7 @@
 # stm32 devices support both JTAG and SWD transports.
 #
 source [find target/swj-dp.tcl]
+source [find mem_helper.tcl]
 
 if { [info exists CHIPNAME] } {
    set _CHIPNAME $CHIPNAME
@@ -11,11 +12,7 @@ if { [info exists CHIPNAME] } {
    set _CHIPNAME stm32f4x
 }
 
-if { [info exists ENDIAN] } {
-   set _ENDIAN $ENDIAN
-} else {
-   set _ENDIAN little
-}
+set _ENDIAN little
 
 # Work-area is a space in RAM used for flash programming
 # By default use 64kB
@@ -86,8 +83,45 @@ if {[using_jtag]} {
  jtag_ntrst_delay 100
 }
 
+reset_config srst_nogate
+
 if {![using_hla]} {
    # if srst is not fitted use SYSRESETREQ to
    # perform a soft reset
    cortex_m reset_config sysresetreq
 }
+
+$_TARGETNAME configure -event examine-end {
+	# Enable debug during low power modes (uses more power)
+	# DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP
+	mmw 0xE0042004 0x00000007 0
+
+	# Stop watchdog counters during halt
+	# DBGMCU_APB1_FZ |= DBG_IWDG_STOP | DBG_WWDG_STOP
+	mmw 0xE0042008 0x00001800 0
+}
+
+$_TARGETNAME configure -event trace-config {
+	# Set TRACE_IOEN; TRACE_MODE is set to async; when using sync
+	# change this value accordingly to configure trace pins
+	# assignment
+	mmw 0xE0042004 0x00000020 0
+}
+
+$_TARGETNAME configure -event reset-init {
+	# Configure PLL to boost clock to HSI x 4 (64 MHz)
+	mww 0x40023804 0x08012008   ;# RCC_PLLCFGR 16 Mhz /8 (M) * 128 (N) /4(P)
+	mww 0x40023C00 0x00000102   ;# FLASH_ACR = PRFTBE | 2(Latency)
+	mmw 0x40023800 0x01000000 0 ;# RCC_CR |= PLLON
+	sleep 10                    ;# Wait for PLL to lock
+	mmw 0x40023808 0x00001000 0 ;# RCC_CFGR |= RCC_CFGR_PPRE1_DIV2
+	mmw 0x40023808 0x00000002 0 ;# RCC_CFGR |= RCC_CFGR_SW_PLL
+
+	# Boost JTAG frequency
+	adapter_khz 8000
+}
+
+$_TARGETNAME configure -event reset-start {
+	# Reduce speed since CPU speed will slow down to 16MHz with the reset
+	adapter_khz 2000
+}