X-Git-Url: https://review.openocd.org/gitweb?a=blobdiff_plain;f=tcl%2Fboard%2Ftelo.cfg;h=126f388f2ad5eec26204b24ef235f548a8d35e0c;hb=f908bae6bfc4b3c403b7e59095749ee33bdd13a5;hp=a0643f74ae6965a8cd1b4eee111151a59b9afc2b;hpb=71af49ca7fb11b0bd0c1ba9578826f49288b68ef;p=openocd.git

diff --git a/tcl/board/telo.cfg b/tcl/board/telo.cfg
index a0643f74ae..126f388f2a 100644
--- a/tcl/board/telo.cfg
+++ b/tcl/board/telo.cfg
@@ -8,47 +8,54 @@ source [find target/c100helper.tcl]
 
 
 # Telo board & C100 support trst and srst
-# however openocd does not support
-# 1. setting srst reset pulse width
-# 2. setting delay between srst pulse and JTAG access
-# This really makes the srst useless for now.
+# Note that libftd2xx.so tries to assert srst
+# which break this script
+# use libftdi.so library instead with this script
+# make the reset asserted to
+# allow RC circuit to discharge for: [ms]
+adapter_nsrst_assert_width 100
+jtag_ntrst_assert_width 100
+# don't talk to JTAG after reset for: [ms]
+adapter_nsrst_delay 100
+jtag_ntrst_delay 100
 reset_config trst_and_srst separate
 
 
 
+
 # issue telnet: reset init
 # issue gdb: monitor reset init
 $_TARGETNAME configure -event reset-init {
-	jtag_khz 100
-	# setup GPIO used as control signals for C100
-	setupGPIO
-	# This will allow acces to lower 8MB or NOR
-	lowGPIO5
-	# setup NOR size,timing,etc.
-	setupNOR
-	# setup internals + PLL + DDR2
-	initC100
+	adapter_khz 100
+	# this will setup Telo board
+	setupTelo
 	#turn up the JTAG speed
-	jtag_khz 3000
-	puts "JTAG speek now 3MHz"
-	puts "type helpC100 to get help on C100"
+	adapter_khz 3000
+	echo "JTAG speek now 3MHz"
+	echo "type helpC100 to get help on C100"
 }
 
 $_TARGETNAME configure -event reset-deassert-post {
 	# Force target into ARM state.
-#	soft_reset_halt # not implemented on ARM11
-	puts "Detected SRSRT asserted on C100.CPU"
+#	soft_reset_halt ;# not implemented on ARM11
+	echo "Detected SRSRT asserted on C100.CPU"
+
+}
 
+$_TARGETNAME configure -event reset-assert-post {
+  echo "Assering reset"
+  #sleep 10
 }
 
-proc power_restore {} { puts "Sensed power restore. No action." }
-proc srst_deasserted {} { puts "Sensed nSRST deasserted. No action." }
+proc power_restore {} { echo "Sensed power restore. No action." }
+proc srst_deasserted {} { echo "Sensed nSRST deasserted. No action." }
 
 
 # boots from NOR on CS0:  8 MBytes CFI flash, 16-bit bus
 # it's really 16MB but the upper 8mb is controller via gpio
 # openocd does not support 'complex reads/writes' to NOR
-flash bank cfi 0x20000000 0x01000000 2 2 $_TARGETNAME
+set _FLASHNAME $_CHIPNAME.flash
+flash bank $_FLASHNAME cfi 0x20000000 0x01000000 2 2 $_TARGETNAME
 
 # writing data to memory does not work without this
-memwrite burst disable
\ No newline at end of file
+arm11 memwrite burst disable