X-Git-Url: https://review.openocd.org/gitweb?a=blobdiff_plain;f=tcl%2Fboard%2Fimx35pdk.cfg;h=b5aa752fa248ec86bd30f9a56a5a785bb2d428fd;hb=bfe1a6c89272c1877308d1e60b5f2798318bb37b;hp=73fa6331d0012e654ce91e0f185b091093018169;hpb=5c98e063b9827ec96194375f383a54cdff31883f;p=openocd.git

diff --git a/tcl/board/imx35pdk.cfg b/tcl/board/imx35pdk.cfg
index 73fa6331d0..b5aa752fa2 100644
--- a/tcl/board/imx35pdk.cfg
+++ b/tcl/board/imx35pdk.cfg
@@ -27,8 +27,8 @@ proc imx35pdk_init { } {
 	mww 0x53f00004 0x77777777
 	
 	# clock setup
-	mww 0x53F80004 0x00821000 # first need to set IPU_HND_BYP
-	mww 0x53F80004 0x00821000 #arm clock is 399Mhz and ahb clock is 133Mhz.
+	mww 0x53F80004 0x00821000 ;# first need to set IPU_HND_BYP
+	mww 0x53F80004 0x00821000 ;#arm clock is 399Mhz and ahb clock is 133Mhz.
 	
 	#=================================================
 	# WEIM config
@@ -122,8 +122,8 @@ proc imx35pdk_init { } {
 	mww 0x43FAC474 0x00000006
 	mww 0x43FAC478 0x00000006
 	mww 0x43FAC47c 0x00000006
-	mww 0x43FAC480 0x00000006	# CSD0
-	mww 0x43FAC484 0x00000006	# CSD1
+	mww 0x43FAC480 0x00000006	;# CSD0
+	mww 0x43FAC484 0x00000006	;# CSD1
 	mww 0x43FAC488 0x00000006
 	mww 0x43FAC48c 0x00000006
 	mww 0x43FAC490 0x00000006
@@ -131,12 +131,12 @@ proc imx35pdk_init { } {
 	mww 0x43FAC498 0x00000006
 	mww 0x43FAC49c 0x00000006
 	mww 0x43FAC4A0 0x00000006	
-	mww 0x43FAC4A4 0x00000006	# RAS
-	mww 0x43FAC4A8 0x00000006	# CAS
-	mww 0x43FAC4Ac 0x00000006	# SDWE
-	mww 0x43FAC4B0 0x00000006 	# SDCKE0
-	mww 0x43FAC4B4 0x00000006  # SDCKE1
-	mww 0x43FAC4B8 0x00000002  # SDCLK
+	mww 0x43FAC4A4 0x00000006	;# RAS
+	mww 0x43FAC4A8 0x00000006	;# CAS
+	mww 0x43FAC4Ac 0x00000006	;# SDWE
+	mww 0x43FAC4B0 0x00000006 	;# SDCKE0
+	mww 0x43FAC4B4 0x00000006  ;# SDCKE1
+	mww 0x43FAC4B8 0x00000002  ;# SDCLK
 	
 	# SDQS0 through SDQS3
 	mww 0x43FAC4Bc 0x00000082
@@ -211,7 +211,7 @@ proc imx35pdk_init { } {
 	# DDR2 : Load reg EMR1 -- OCD default
 	mwb 0x82000780 0xda
 	# DDR2 : Load reg EMR1 -- OCD exit
-	mwb 0x82000400 0xda	# ODT disabled
+	mwb 0x82000400 0xda	;# ODT disabled
 	
 	# ESD_ESDCTL0 : select normal-operation mode
 	# DSIZ=32-bit, BL=8, COL=10-bit, ROW=13-bit
@@ -229,10 +229,10 @@ proc imx35pdk_init { } {
 	# Adjust the ESDCDLY5 register
 	#***********************************************
 	# Vary DQS_ABS_OFFSET5 for writes
-	mww 0xB8001020 0x00F48000	# this is the default value
-	mww 0xB8001024 0x00F48000	# this is the default value
-	mww 0xB8001028 0x00F48000	# this is the default value
-	mww 0xB800102c 0x00F48000	# this is the default value
+	mww 0xB8001020 0x00F48000	;# this is the default value
+	mww 0xB8001024 0x00F48000	;# this is the default value
+	mww 0xB8001028 0x00F48000	;# this is the default value
+	mww 0xB800102c 0x00F48000	;# this is the default value
 	
 	
 	#Then you can make force measure with the dedicated bit (Bit 7 at ESDMISC)