X-Git-Url: https://review.openocd.org/gitweb?a=blobdiff_plain;f=src%2Ftarget%2Ftarget%2Fzy1000.cfg;h=d8bb46502f74c2186d68bfe731228c97f61a35fd;hb=503bb08f9993c59a4b3206600555a42fd18459b6;hp=e6929f222fcbc7cf0e657d2cfcf09cbdd5885cf6;hpb=75e69503b9ca22136e261f889058e003b4622286;p=openocd.git

diff --git a/src/target/target/zy1000.cfg b/src/target/target/zy1000.cfg
index e6929f222f..d8bb46502f 100644
--- a/src/target/target/zy1000.cfg
+++ b/src/target/target/zy1000.cfg
@@ -1,30 +1,110 @@
-#Script for ZY1000
-
-#Atmel ties SRST & TRST together, at which point it makes
-#no sense to use TRST, but use TMS instead.
-#
-#The annoying thing with tying SRST & TRST together is that
-#there is no way to halt the CPU *before and during* the
-#SRST reset, which means that the CPU will run a number
-#of cycles before it can be halted(as much as milliseconds).
-reset_config srst_only srst_pulls_trst
- 
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
-
-#target configuration
-#target arm7tdmi <endianness> <reset mode> <chainpos> <variant>
-target arm7tdmi little reset_init 0 arm7tdmi-s_r4
-
-# at CPU CLK <32kHz this must be disabled
-arm7 fast_memory_access enable
-arm7_9 dcc_downloads enable
-
-
-flash bank ecosflash 0x01000000 0x200000 2 2 0 /rom/at91eb40a.elf
-target_script 0 reset event/zy1000_reset.script
-
-# required for usable performance. Used for lots of
-# other things than flash programming.
-working_area 0 0x00000000 0x20000 nobackup
+#Script for ZY1000
+
+#Atmel ties SRST & TRST together, at which point it makes
+#no sense to use TRST, but use TMS instead.
+#
+#The annoying thing with tying SRST & TRST together is that
+#there is no way to halt the CPU *before and during* the
+#SRST reset, which means that the CPU will run a number
+#of cycles before it can be halted(as much as milliseconds).
+reset_config srst_only srst_pulls_trst
+
+
+if { [info exists CHIPNAME] } {	
+   set  _CHIPNAME $CHIPNAME    
+} else {	 
+   set  _CHIPNAME zy1000
+}
+
+if { [info exists ENDIAN] } {	
+   set  _ENDIAN $ENDIAN    
+} else {	 
+   set  _ENDIAN little
+}
+
+ 
+#jtag scan chain
+if { [info exists CPUTAPID ] } {
+   set _CPUTAPID $CPUTAPID
+} else {
+   set _CPUTAPID 0x1f0f0f0f
+}
+jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+
+set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
+target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4
+
+# at CPU CLK <32kHz this must be disabled
+arm7_9 fast_memory_access enable
+arm7_9 dcc_downloads enable
+
+flash bank ecosflash 0x01000000 0x200000 2 2 0 ecos/at91eb40a.elf
+$_TARGETNAME configure -event reset-init { 
+	# Set up chip selects & timings
+	mww 0xFFE00000 0x0100273D
+	mww 0xFFE00004 0x08002125
+	mww 0xFFEe0008 0x02002125
+	mww 0xFFE0000c 0x03002125
+	mww 0xFFE00010 0x40000000
+	mww 0xFFE00014 0x50000000
+	mww 0xFFE00018 0x60000000
+	mww 0xFFE0001c 0x70000000
+	mww 0xFFE00020 0x00000001
+	mww 0xFFE00024 0x00000000
+	
+	# remap  
+	mww 0xFFFFF124 0xFFFFFFFF  
+	mww 0xffff0010 0x100
+	mww 0xffff0034 0x100
+	
+	#disable 16x5x UART interrupts
+	mww 0x08020004 0
+}
+
+# required for usable performance. Used for lots of
+# other things than flash programming.
+$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00020000 -work-area-size 0x20000 -work-area-backup 0
+
+jtag_khz 16000
+
+
+proc production_info {} {
+	return "Serial number is official MAC number. Format XXXXXXXXXXXX"
+}
+
+# There is no return value from this procedure. If it is
+# successful it does not throw an exception
+#
+# Progress messages are output via puts 
+proc production {firmwarefile serialnumber} {
+	if {[string length $serialnumber]!=12} {
+		puts "Invalid serial number"
+		return
+	}
+
+	puts "Power cycling target"
+	power off
+	sleep 3000
+	power on
+	sleep 1000
+	reset init
+	flash write_image erase $firmwarefile 0x1000000 bin
+	verify_image $firmwarefile 0x1000000 bin
+
+	# Big endian... weee!!!!
+	puts "Setting MAC number to $serialnumber"	
+	flash fillw [expr 0x1030000-0x8] "0x[string range $serialnumber 2 3][string range $serialnumber 0 1]0000" 1
+	flash fillw [expr 0x1030000-0x4] "0x[string range $serialnumber 10 11][string range $serialnumber 8 9][string range $serialnumber 6 7][string range $serialnumber 4 5]" 1
+	puts "Production successful"
+} 
+
+
+proc production_test {} {
+	power on
+	sleep 1000
+	target_request debugmsgs enable
+	reset run
+	sleep 25000
+	target_request debugmsgs disable
+	return "See IP address above..."
+}